A strong transom bracket should match your intended job: mounting an auxiliary outboard, reinforcing the transom, or supporting the motor while trailering. The Marinebaby Boat Motor Bracket is a clear fit for small 7.5–20 HP two-stroke motors, while the Vinland Marine 20 HP Bracket adds a stated 115-pound weight capacity. These products are not interchangeable: reinforcement plates distribute mounting loads, and transom savers brace a motor during transport rather than attach it as a working engine mount.
This roundup compares all three types and highlights the specifications that distinguish them, including motor capacity, adjustment, plate thickness, and mounting pattern. Check your boat’s transom layout and engine requirements before choosing; product descriptions do not establish compatibility with every hull or motor.
The Marinebaby Boat Motor Bracket is the best overall choice when you need a working auxiliary outboard mount for a small motor: it is specified for 7.5–20 HP two-stroke motors and offers five locking height positions. If you need a 20 HP mount with a stated weight limit, consider the Vinland Marine 20 HP Bracket, rated for up to 115 pounds. For reinforcing an existing engine mounting area rather than adding a motor, choose a support plate instead.
Our Top Picks
Best OverallThis working motor mount is specified for 7.5–20 HP two-stroke motors and provides five locking height positions from 195 to 320 mm.
View on Amazon
Best Capacity DetailA spring-loaded auxiliary motor mount with five vertical positions, a reinforced welded frame, and a stated limit of 20 HP and 115 pounds.
View on Amazon
Best Single-Engine BracketALMULOO 20-Inch Engine Bracket
This is explicitly a heavy-duty 20-inch single-engine bracket, made from aluminum with a powder-coated finish for marine use.
View on Amazon- Best Two-Plate Kit Camoo TSP-1 and TSP-2DP Plates
- Thickest Plate ZOMTHKS Reinforcement Plate
Compare These Transom Brackets and Support Options
| # | Product | Material | Weight | Material Type | Buy |
|---|---|---|---|---|---|
| 1 | 1. Marinebaby Boat Motor BracketBest Overall | Aluminum | 4.94 kg | Aluminum | View on Amazon |
| 2 | 2. Vinland Marine 20 HP BracketBest Capacity Detail | Nylon Base | — | Nylon Base | View on Amazon |
| 3 | 3. ALMULOO 20-Inch Engine BracketBest Single-Engine Bracket | Aluminum | — | Aluminum | View on Amazon |
| 4 | 4. Camoo TSP-1 and TSP-2DP PlatesBest Two-Plate Kit | Cast Aluminum | — | — | View on Amazon |
| 5 | 5. ZOMTHKS Reinforcement PlateThickest Plate | Aluminum | 3 lb | Aluminum | View on Amazon |
| 6 | 6. Generic Full-Pattern Backing PlateFull-pattern aluminum backing plate | Aluminum | 3.3 lb | Aluminum | View on Amazon |
| 7 | 7. Danti TSP-1 Support PlateSingle top-hole reinforcement plate | Aluminum | — | Aluminum | View on Amazon |
| 8 | 8. JY PERFORMANCE Transom SaverAdjustable trailer transom saver | Acrylonitrile Butadiene Styrene (ABS), Aluminum | 1.67 kg | Acrylonitrile Butadiene Styrene (ABS), Aluminum | View on Amazon |
| 9 | 9. Viibrra Adjustable Transom SaverAdjustable saver with dual mounts | Composite, Stainless Steel | — | — | View on Amazon |
| 10 | 10. Mangrove Products Transom Saver WedgeSingle-ram trailering wedge support | Mangrove Products EPDM Rubber Formula | 0.38 kg | Mangrove Products EPDM Rubber Formula | View on Amazon |
Detailed Reviews: Best Transom Bracket For Outboard

#1 · Best Overall
1. Marinebaby Boat Motor Bracket
- Material: Aluminum
- Weight: 4.94 kg
- Material Type: Aluminum
Best for: Small two-stroke adjustable motor mount.
Why it ranks #1: This working motor mount is specified for 7.5–20 HP two-stroke motors and provides five locking height positions from 195 to 320 mm.
Five locking height positions span 195 to 320 millimeters, giving this Marinebaby bracket adjustable mounting height for 7.5-to-20-horsepower two-stroke motors. Stainless-steel counterbalance springs help carry motor weight, while a solid polypropylene mounting board provides the engine's mounting surface.
The five-position adjustment from 195 to 320 millimeters lets owners select among specified mounting heights, and the counterbalance springs are intended to balance motor weight during adjustment. Its stated fit is for two-stroke motors from 7.5 to 20 horsepower. The aluminum bracket and polypropylene mounting board form the support assembly, with an 8-by-10.2-inch overall size listed. Mounting hardware is not included, and the listing calls for 8-millimeter screws, so installation requires sourcing that hardware separately.
- Five locking height positions from 195 to 320 millimeters
- Stainless-steel springs counterbalance motor weight
- Listed for 7.5-to-20-horsepower two-stroke motors
- Solid polypropylene mounting board
- Mounting hardware is not included; the listing requires 8-millimeter screws.
Skip it if you have a four-stroke motor or need mounting hardware included with the bracket.
This bracket fits buyers mounting a listed 7.5-to-20-horsepower two-stroke motor who value multiple height positions and spring counterbalance. Account for the required 8-millimeter screws, which are not included, when planning installation.
Full product details
| Brand | Marinebaby |
|---|---|
| Color | Silver / Black |
| Item Weight | 4.94 kg |
| Manufacturer | CHENGZHOU |
| Part Number | CZX7953AA |
| Material | Aluminum |
| Model Number | CZX7953AA |
Listed on Amazon as: Boat Outboard Motor Bracket, Aluminum Boat Engine Support 20 HP
View on Amazon
#2 · Best Capacity Detail
2. Vinland Marine 20 HP Bracket
- Material: Nylon Base
- Material Type: Nylon Base
Best for: 20-horsepower kicker motor mount.
Why it ranks #2: A spring-loaded auxiliary motor mount with five vertical positions, a reinforced welded frame, and a stated limit of 20 HP and 115 pounds.
Five vertical positions and torsion springs make this Vinland Marine bracket adjustable for auxiliary motors up to 20 horsepower and 115 pounds. Its reinforced welded frame and wide-track body provide the listed support structure, while a black polypropylene mounting base suits use on jon boats, bass trackers, or canoes.
The spring-loaded, five-position bracket lets buyers raise or lower a kicker motor among defined positions, while torsion springs counterbalance the engine during adjustment. Vinland Marine lists capacity up to 20 horsepower and 115 pounds, giving a clear boundary for selecting a motor. The 304 stainless-steel bracket and polypropylene base combine the stated structural materials, and the wide-track body is intended to add stability. The listing also identifies jon boats, bass trackers, and canoes as suitable uses.
- Five vertical adjustment positions with torsion springs
- Capacity listed up to 20 horsepower and 115 pounds
- 304 stainless-steel bracket with reinforced welded frame
- Polypropylene base and wide-track body
- The listed capacity stops at 20 horsepower and 115 pounds.
Skip it if your motor exceeds 20 horsepower or 115 pounds; Marinebaby CZX7953AA is also listed only up to 20 horsepower.
This suits owners mounting a kicker motor within the stated 20-horsepower and 115-pound limits on a jon boat, bass tracker, or canoe. Its five-position spring-loaded design offers adjustment, but it is not specified for heavier motors.
Full product details
| Brand | Vinland Marine |
|---|---|
| Color | Black |
| Included Components | Auxiliary Outboard Motor Bracket for 20hp |
| Item Dimensions | 21 x 9 x 8.5 inches |
| Dimensions | 21 x 9 x 8.5 inches |
| Manufacturer | Vinland Marine |
| Material | Nylon Base |
| Model Number | 7951S |
Listed on Amazon as: Outboard Motor Mount Bracket for 20hp Outboard Motor w/Black PP Base, Kicker Motor Bracket, Canoe Motor mounting Bracket, Boat Motor Mount, Lift up Jack Plate, transom Board
View on Amazon
#3 · Best Single-Engine Bracket
3. ALMULOO 20-Inch Engine Bracket
- Material: Aluminum
- Material Type: Aluminum
Best for: 20-inch single-engine bracket buyers.
Why it ranks #3: This is explicitly a heavy-duty 20-inch single-engine bracket, made from aluminum with a powder-coated finish for marine use.
A 20-inch single-engine bracket pairs heavy-duty aluminum with a powder-coated exterior for marine use. Its stated compatibility includes Mercury, Yamaha, Evinrude, Honda, and Johnson boats, giving buyers of those outboards a bracket option with a protective finish and installation accessories included.
The 20-inch specification identifies the bracket size, while its single-engine configuration clarifies the intended setup. ALMULOO describes the aluminum body as heavy-duty and the powder-coated surface as a durable protective layer for marine conditions. The stated compatibility names several major outboard brands, including Mercury, Yamaha, Evinrude, Honda, and Johnson. Installation accessories are included, but the supplied details do not give a horsepower capacity or adjustment range, so buyers needing either figure should not infer it from the material or size.
- 20-inch outboard bracket size is specified
- Configured for a single engine
- Heavy-duty aluminum construction
- Powder-coated exterior and installation accessories are listed
- No horsepower capacity or adjustment range is specified in the supplied details.
Skip it if you need a documented horsepower limit or adjustment range before selecting an engine bracket.
This bracket suits buyers seeking a 20-inch single-engine option with aluminum construction and a powder-coated finish. Its compatibility list covers several named outboard brands, but the supplied specifications do not state a horsepower rating or adjustment range.
Full product details
| Brand | ALMULOO |
|---|---|
| Color | White |
| Included Components | 1 × outboard engine bracket and installation accessories. |
| Manufacturer | AINUOSEN LLC |
| Part Number | VC-0448 |
| Material | Aluminum |
| Model Number | VC-0448 |
Listed on Amazon as: Universal Heavy Duty Aluminium 20" Outboard Single Engine Bracket
View on Amazon
#4 · Best Two-Plate Kit
4. Camoo TSP-1 and TSP-2DP Plates
- Material: Cast Aluminum
Best for: Top-and-lower bolt-hole reinforcement.
Why it ranks #4: The kit includes top- and lower-hole support plates, with stated dimensions and a universal mounting pattern for major outboard manufacturers.
Two cast-aluminum plates cover both standard transom bolt-hole positions: a 15-inch TSP-1 for the top holes and a 12-inch TSP-2DP for the lower holes. The paired layout gives buyers reinforcing plates for both mounting areas, rather than a single plate for only one set of bolts.
The TSP-1 and TSP-2DP are specified for standard top and lower bolt holes, respectively, and the listing says their pattern matches universal outboard mounting patterns used by major manufacturers including Mercury, Evinrude, Johnson, and Yamaha. That pairing helps distribute engine mounting stress at both bolt-hole areas. Cast-aluminum construction provides the plates, while their different lengths and the lower plate's listed 10-inch hole spacing distinguish their positions. This is bolt-hole reinforcement, not a motor-support bracket for trailering.
- Includes one plate for standard top bolt holes and one for lower bolt holes
- TSP-1 measures 15 by 2 inches
- TSP-2DP measures 12 by 2 inches with 10-inch hole spacing
- Cast-aluminum plates are listed for major outboard mounting patterns
- The kit is limited to transom bolt-hole reinforcement, not trailering support.
Skip it if you need an adjustable motor bracket or a trailering support rather than plates around mounting bolts.
Choose this paired kit when your priority is reinforcing both standard top and lower outboard bolt-hole areas. Its listed role is transom support at the mounting bolts, so it does not replace a bracket that carries or supports an engine during transport.
Full product details
| Brand | Camoo |
|---|---|
| Color | Silver |
| Included Components | 1 x TSP-1 Transom Support Plate, 1 x TSP-2DP Transom Support Plate |
| Item Package Dimensions L x W x H | 15.51 x 4.13 x 1.3 inches |
| Manufacturer | Camoo |
| Material | Cast Aluminum |
| Package Weight | 0.97 kg |
Listed on Amazon as: TSP-1 & TSP-2DP Transom Support Plate Kit For Transom Top & Lower Bolt Hole
View on Amazon
#5 · Thickest Plate
5. ZOMTHKS Reinforcement Plate
- Material: Aluminum
- Weight: 3 lb
- Material Type: Aluminum
Best for: Broad aluminum transom backing.
Why it ranks #5: Its 0.2-inch aluminum plate measures 16 by 14 inches and is described as distributing outboard load across the transom.
A 16-by-14-inch, 5-millimeter-thick aluminum plate spreads outboard load across a broad transom area. ZOMTHKS says the reinforcement helps reduce bolt stress and puncture damage on fiberglass or wood-cored boats, giving owners of those transoms a larger backing surface than a narrow bolt-hole strip.
The listed 5-millimeter thickness and 16-by-14-inch dimensions make this a broad, single-piece reinforcement plate rather than a paired top-and-lower kit. Its aluminum is described as corrosion-resistant for marine conditions, and the wide format is intended to distribute engine load across the transom. The listing specifically connects that load spreading with reduced bolt stress and puncture damage on fiberglass or wood-cored boats. It is reinforcement at the engine mounting area, not a height-adjustable engine bracket.
- One-piece plate measures 16 by 14 inches
- 5-millimeter thickness is specified
- Listing describes load distribution to reduce bolt stress
- Intended to help prevent puncture damage on fiberglass or wood-cored transoms
- The package includes one plate, rather than a paired set for separate bolt-hole positions.
Skip it if you want a paired top-and-lower bolt-hole kit; Camoo's TSP-1 and TSP-2DP set supplies plates for both positions.
Consider this broad backing plate when reinforcing a fiberglass or wood-cored transom is the priority. Its single-piece format and stated dimensions suit buyers seeking area coverage, but it is not an adjustable mount or a transport brace for the outboard.
Full product details
| Brand | ZOMTHKS |
|---|---|
| Color | Silver |
| Included Components | 1 X transom support plate |
| Item Dimensions | 16 x 14 x 0.3 inches |
| Item Weight | 3 pounds |
| Dimensions | 16 x 14 x 0.3 inches |
| Manufacturer | ZOMTHKS |
| Part Number | QYLB-316 |
| Material | Aluminum |
| Model Number | QYLB-316 |
Listed on Amazon as: 1 Pcs Outboard Transom Reinforcement Plate 0.2" Thick Aluminum Support
View on Amazon
#6
6. Generic Full-Pattern Backing Plate
- Material: Aluminum
- Weight: 3.3 lb
- Material Type: Aluminum
Best for: Full-pattern aluminum backing plate.
Why it ranks #6: The 0.2-inch aluminum backing plate uses a full-pattern design and is listed as compatible with most outboards.
The 0.2-inch-thick aluminum plate uses a full-pattern design for comprehensive outboard transom reinforcement. Its stated compatibility with most outboards gives buyers a broad-pattern option when they want backing support across the engine mounting area, rather than a plate specified only for upper or lower bolt holes.
The full-pattern layout is presented as providing comprehensive reinforcement, while the 0.2-inch aluminum construction is described as durable and corrosion-resistant. Together, those features make this a backing plate intended to support an outboard's transom mounting area in marine conditions. The listed dimensions are 14 by 7.8 by 0.79 inches, giving buyers physical sizing information for planning the installation. The listing says most outboards, but does not specify a particular bolt-hole layout or engine capacity.
- Full-pattern design is intended to provide comprehensive reinforcement
- Aluminum plate is 0.2 inch thick
- Corrosion resistance is specified
- Listed dimensions are 14 by 7.8 by 0.79 inches
- The listing gives no specific bolt-hole spacing or engine-capacity limit.
Skip it if you require stated bolt-hole spacing or an engine-capacity rating before choosing a backing plate.
This is a candidate for owners seeking full-pattern aluminum reinforcement and whose mounting arrangement suits the plate's listed dimensions. Because the listing does not state hole spacing or a capacity, it is less suited to buyers who need those specifications documented.
Full product details
| Brand | Generic |
|---|---|
| Color | Aluminum Raw Color |
| Included Components | Engine |
| Item Dimensions | 14 x 7.8 x 0.79 inches |
| Item Weight | 3.3 pounds |
| Dimensions | 14 x 7.8 x 0.79 inches |
| Manufacturer | BOFi-00F79 |
| Part Number | BOFi-00F79 |
| Material | Aluminum |
| Model Number | BOFi-00F79 |
Listed on Amazon as: Outboard Transom Reinforcement Backing Plate for Outboard Motors, 0.2" Thick, Full Pattern, Durable Aluminum, Compatible with Most Outboards
View on Amazon
#7
7. Danti TSP-1 Support Plate
- Material: Aluminum
- Material Type: Aluminum
Best for: Single top-hole reinforcement plate.
Why it ranks #7: A 15-by-2-inch, 3/8-inch aluminum plate for standard top bolt holes, intended to distribute engine-bolt stress and protect the transom.
A 15-by-2-inch aluminum TSP-1 plate targets standard top bolt holes on outboards without twist clamps. That focused fit gives owners a way to spread engine-bolt stress across the transom, with compatibility listed for common Mercury, Evinrude, Johnson, and Yamaha mounting patterns.
Danti identifies this as a TSP-1 plate for top bolt holes and specifies a 15-by-2-inch size, making its intended position more specific than a full multi-position reinforcement kit. Its aluminum construction is described as corrosion- and rust-resistant for marine use. The listing says it distributes engine weight and bolt stress to protect the transom, and targets outboards without twist clamps; buyers should treat it as stationary transom reinforcement, not a transport support.
- TSP-1 configuration is for standard top bolt holes
- 15-by-2-inch plate size is specified
- Aluminum construction is described as corrosion- and rust-resistant
- Listed for outboards without twist clamps and common mounting patterns
- Only the top-hole TSP-1 plate is included; lower-hole reinforcement is not listed.
Skip it if you need both upper and lower bolt-hole plates; Camoo's TSP-1 and TSP-2DP kit includes both positions.
This suits owners seeking a single top-hole reinforcement plate for an outboard without twist clamps. Its stated scope is the upper bolt area, so buyers wanting reinforcement at lower bolt holes or support while trailering should choose a different type of product.
Full product details
| Brand | Danti |
|---|---|
| Color | Silver |
| Manufacturer | Wen wen top |
| Part Number | 3001-8067 |
| Material | Aluminum |
| Model Number | 3001-8067 |
| Recommended Uses | protecting the transom of outboard motors without twist clamps |
Listed on Amazon as: Transom Support Plate TSP-1 Outboard Motor Aluminum Transom Support Plate For Top Bolt Holes Standard Bolt Holes 15" X 2", 3/8" Thickness
View on Amazon
#8
8. JY PERFORMANCE Transom Saver
- Material: Acrylonitrile Butadiene Styrene (ABS), Aluminum
- Weight: 1.67 kg
- Material Type: Acrylonitrile Butadiene Styrene (ABS), Aluminum
Best for: Adjustable trailer transom saver.
Why it ranks #8: This trailering support adjusts from 23 to 35 inches and is specified for motors up to 100 HP; it is not a working engine mount.
A telescoping shaft adjusts from 23 to 35 inches and is listed for outboards up to 100 horsepower. That range lets owners set the support length for a motor and trailer arrangement where engine-to-ground clearance is limited, while the composite head and ABS clamp hold the engine during transport.
The adjustable 23-to-35-inch shaft gives buyers a way to set support length, and the stated 100-horsepower limit defines its listed engine range. JY PERFORMANCE describes the saver as distributing weight when ground clearance is limited. A composite head with a marine-grade ABS clamp holds the motor, while the included trailer-mount bracket provides the mounting point. The listed kit also includes clevis pins with retainers and rubber strings with S-hooks; this is a transport support, not a transom bolt-hole plate.
- Adjusts from 23 to 35 inches
- Listed for motors up to 100 horsepower
- Composite head and marine-grade ABS clamp hold the engine
- Trailer-mount bracket, clevis pins, and S-hook rubber strings are included
- Its listed role is trailering support, not reinforcement of transom mounting bolts.
Skip it if you need reinforcement around the engine's transom bolt holes rather than a support for trailering.
Choose this adjustable saver for trailering an outboard up to the stated 100-horsepower limit, especially where ground clearance is constrained. Its function is transport support; it does not serve as a backing plate for engine mounting bolts.
Full product details
| Brand | JY PERFORMANCE |
|---|---|
| Color | Black+Silver |
| Included Components | 2 x 23'' rubber string with S-hooks, 2 x Clevis pin with a retainer, Boat transom saver with composite head, Telescoping shaft, Trailer mount bracket |
| Item Weight | 1.67 kg |
| Manufacturer | JY PERFORMANCE |
| Part Number | DAC968 |
| Manufacturer Warranty Description | 1 year |
| Material | Acrylonitrile Butadiene Styrene (ABS), Aluminum |
| Model Number | DAC968 |
Listed on Amazon as: Boat Transom Saver for Outboard Motor, Supports up to 100 HP Motors
View on Amazon
#9
9. Viibrra Adjustable Transom Saver
- Material: Composite, Stainless Steel
Best for: Adjustable saver with dual mounts.
Why it ranks #9: The 23–35-inch support is specified for motors up to 100 HP and includes roller and trailer mounting brackets for transport support.
Two mounting options—a roller bracket and a standard trailer bracket—let this adjustable saver suit different trailer setups. Its 23-to-35-inch range and stated 100-horsepower limit define the listed size and motor scope, while the support is intended to absorb road shocks during transport.
The 23-to-35-inch adjustment gives owners a range for setting the support between trailer and engine, and the two included mounting brackets accommodate roller or standard trailer mounting arrangements. Viibrra says the saver absorbs road shocks and reduces pressure on the transom and hydraulic tilt-trim parts during transport. One important operating condition is explicit: the motor must have factory power trim or tilt for the product to work properly. It is a trailering support, not a bolt-hole reinforcement plate.
- Adjusts from 23 to 35 inches
- Listed for motors up to 100 horsepower
- Includes roller and standard trailer mounting brackets
- Intended to absorb road shocks and reduce transom and tilt-trim pressure
- Requires factory power trim or tilt to work properly.
Skip it if you have no factory power trim or tilt; JY PERFORMANCE DAC968 is listed without that stated operating requirement.
Choose this saver for trailering a motor within its stated 100-horsepower scope when the trailer uses a roller or standard bracket. It requires factory power trim or tilt, so that operating condition is central to fit.
Full product details
| Brand | Viibrra |
|---|---|
| Color | Silver |
| Included Components | Boat Transom Saver, Composite Engine Head, Roller Mount, Trailer Mount |
| Item Package Dimensions L x W x H | 17.8 x 6.1 x 2.6 inches |
| Manufacturer | Viibrra |
| Material | Composite, Stainless Steel |
| Model | Boat Transom Saver Adjustable |
| Package Weight | 1.43 kg |
| Warranty Description | 1 Year |
Listed on Amazon as: Boat Transom Saver, Adjustable 23‐35 Inches 100HP Outboard Motor Support
View on Amazon
#10
10. Mangrove Products Transom Saver Wedge
- Material: Mangrove Products EPDM Rubber Formula
- Weight: 0.38 kg
- Material Type: Mangrove Products EPDM Rubber Formula
Best for: Single-ram trailering wedge support.
Why it ranks #10: This EPDM wedge braces a single-ram hydraulic-tilt outboard while trailering, but it is not a transom-mounted motor bracket.
A molded EPDM rubber wedge with ten inner notches targets outboards using single-ram hydraulic tilt systems. Mangrove Products lists it for supporting the motor during trailering, helping limit unwanted up-and-down travel that can put pressure on the hydraulic tilt-and-trim system and boat transom.
The single-ram fit is the key compatibility boundary: this wedge is specified for outboards with single-ram hydraulic tilt systems, and the listing directs buyers to a fitment guide. Its EPDM rubber formula and ten molded inner notches form the stated support block, while its intended trailering role is to brace the motor against unwanted movement. The block's compact 5.2-by-2.13-by-2.13-inch dimensions distinguish it from an adjustable shaft-style saver or a transom reinforcement plate.
- Specified for outboards with single-ram hydraulic tilt systems
- EPDM rubber formula construction
- Molded design has ten inner notches
- Intended to brace the motor during trailering
- Fitment is limited to outboards with single-ram hydraulic tilt systems.
Skip it if your outboard does not use a single-ram hydraulic tilt system or needs an adjustable shaft support.
Choose this compact wedge for trailering an outboard whose single-ram hydraulic tilt system matches the stated fitment. It braces the motor rather than reinforcing transom bolt holes, and its fitment guide is relevant to selecting the intended application.
Full product details
| Brand | Mangrove Products |
|---|---|
| Color | Black |
| Included Components | MGP's EPDM Rubber Formula TS-Block, MGP's Secure Fit Molded 10 Inner Notches |
| Item Dimensions | 5.2 x 2.13 x 2.13 inches |
| Item Weight | 0.38 kg |
| Dimensions | 5.2 x 2.13 x 2.13 inches |
| Manufacturer | Mangrove Products |
| Part Number | EA-2NL9-HGGP |
| Material | Mangrove Products EPDM Rubber Formula |
| Model Number | 2148 |
Listed on Amazon as: Transom Saver Wedge, Outboard Motor Support, Single Ram, Pontoon Boat Accessories
View on AmazonMounting bracket, backing plate, or trailering support?
The first compatibility check is the job the part performs: only a motor mount is intended to hold an auxiliary engine for operation. The Marinebaby Boat Motor Bracket and Vinland Marine 20 HP Bracket are adjustable engine mounts; the ALMULOO 20-Inch Engine Bracket is described as a single-engine bracket, though its listing gives no engine-capacity figure. By contrast, the Camoo TSP-1 and TSP-2DP Plates, ZOMTHKS Reinforcement Plate, Generic Full-Pattern Backing Plate, and Danti TSP-1 Support Plate reinforce mounting areas.
They do not provide the adjustable motor support described by the mount products. The JY PERFORMANCE Transom Saver, Viibrra Adjustable Transom Saver, and Mangrove Products Transom Saver Wedge support an outboard during trailering.
Treating a saver or plate as a replacement engine mount risks choosing a product for the wrong load and use. Confirm the part’s intended function before comparing size or material.
Check the fit details the listings leave open
A stated universal fit does not replace checking your boat’s hole spacing, transom dimensions, and engine requirements. For example, the Camoo TSP-1 and TSP-2DP Plates specify separate top and lower bolt-hole plates, while the Danti TSP-1 Support Plate lists a 15-by-2-inch size for standard top holes. Those details can help you compare layouts, but the listings do not provide a complete measurement guide for every boat.
Adjustable mounts also differ: Marinebaby gives a five-position height range, while Vinland Marine specifies five vertical positions and a 20 HP, 115-pound limit. Trailering supports bring another fit trap: Viibrra says the motor must have factory power trim or tilt, and the Mangrove Products Transom Saver Wedge is intended for single-ram hydraulic tilt systems.
Verify the actual mounting pattern and support-system fit before ordering; the product descriptions alone cannot confirm fit on a particular boat.
How to Choose an Outboard Transom Bracket
Intended job and engine capacity
Start by deciding whether you need an operating motor mount, transom reinforcement, or trailering support. The Marinebaby Boat Motor Bracket is listed for 7.5–20 HP two-stroke motors, and the Vinland Marine 20 HP Bracket specifies up to 20 HP and 115 pounds. The ALMULOO 20-Inch Engine Bracket is described as a single-engine bracket but gives no capacity figure in the supplied facts.
Reinforcement plates are a different choice: they spread mounting loads, rather than serving as a separate motor mount. The JY PERFORMANCE Transom Saver and Viibrra Adjustable Transom Saver support motors up to 100 HP during transport.
Choose a rated mount for an auxiliary engine; choose a plate for reinforcement or a saver for trailering.
Adjustment and mounting layout
Compare the mounting arrangement and adjustment range with your boat and motor rather than assuming that universal wording guarantees fit. The Marinebaby Boat Motor Bracket has five locking height positions from 195 to 320 mm, while the Vinland Marine 20 HP Bracket lists five vertical positions. For reinforcement, the Camoo TSP-1 and TSP-2DP Plates cover standard top and lower bolt holes, and the Danti TSP-1 Support Plate is sized for standard top holes.
Trailering supports adjust differently: the JY PERFORMANCE Transom Saver and Viibrra Adjustable Transom Saver extend from 23 to 35 inches. An adjustable auxiliary mount favours buyers whose setup needs height selection; a hole-specific plate favours buyers matching an existing mounting pattern.
Measure before selecting either.
Material, thickness, and support design
Choose construction according to the part’s function and the specifications that are actually stated. The ZOMTHKS Reinforcement Plate and Generic Full-Pattern Backing Plate are both 0.2-inch aluminum; the Camoo TSP-1 and TSP-2DP Plates and Danti TSP-1 Support Plate list 3/8-inch aluminum. For adjustable motor mounts, Marinebaby specifies an aluminum bracket with a polypropylene mounting board, while Vinland Marine uses a stainless-steel bracket with a black polypropylene base.
Trailering supports use other designs: JY PERFORMANCE combines an aluminum shaft with a composite head, and the Mangrove Products Transom Saver Wedge uses EPDM rubber. Buyers choosing a backing plate can compare the listed thicknesses; buyers choosing a working mount or transport support should prioritize its stated function and fit instead.
Which Outboard Transom Bracket Should You Choose?
For a small auxiliary two-stroke outboard, choose the Marinebaby Boat Motor Bracket: its 7.5–20 HP range and five height positions are clearly stated. If you need a 20 HP mount with an explicit weight limit, the Vinland Marine 20 HP Bracket specifies capacity up to 115 pounds. The ALMULOO 20-Inch Engine Bracket suits shoppers seeking a single-engine bracket, but confirm its capacity and mounting fit because those details are not supplied here.
To reinforce existing top and lower bolt holes, consider the Camoo TSP-1 and TSP-2DP Plates; for transport support, choose a transom saver that matches your motor and trailer arrangement. In particular, verify Viibrra’s power-trim requirement or the Mangrove wedge’s single-ram hydraulic-tilt fit before buying.
Related Buying Guides
Frequently Asked Questions
How do I measure my boat’s transom and mounting-hole pattern before buying a bracket?
Measure the transom’s thickness and available mounting area, then record the distance between existing bolt-hole centers both horizontally and vertically. Compare those measurements with the bracket’s stated hole pattern and required clearances. If dimensions or drilling details are missing, confirm compatibility with the manufacturer or a qualified marine installer before ordering or modifying the transom.
Does a transom saver fit my trailer and outboard’s tilt or trim system?
It fits only if its length, contact points, and attachment method suit your trailer and motor arrangement. Check the saver’s adjustment range and whether it is intended for your outboard’s tilt or trim setup; some designs have specific requirements. Confirm the motor can be supported securely without interfering with trailer movement or other equipment.
How should I inspect a transom for damage before adding an outboard or reinforcement plate?
Look for soft or swollen areas, cracks, loose fasteners, water intrusion, and separation around the mounting holes. Check both sides of the transom and the surrounding structure, and investigate any movement or discoloration rather than covering it with a plate. If you find suspected rot, structural damage, or uncertainty about strength, seek a qualified marine professional’s assessment before mounting a motor.
When should I choose a reinforcement plate instead of a motor bracket?
Choose a reinforcement plate when your goal is to spread or support loads around existing mounting holes, not to add a motor. A motor bracket is the relevant category when you need a mounting structure for an auxiliary outboard. Confirm the plate’s hole pattern and fit with your transom; a plate does not by itself establish that the transom is structurally sound.
What should I verify before choosing a transport support for my outboard?
Check the support’s fit with your motor, trailer, and the motor’s tilt or trim arrangement. Match any stated adjustment range or power-trim, hydraulic-tilt, or ram requirements to your setup, and confirm the support contacts the intended points securely. Do not assume that a general-purpose label guarantees compatibility; the product’s specific fit conditions matter.
Final Words
For a working small auxiliary outboard, the Marinebaby is the clearest overall pick here: its stated 7.5–20 HP range and five locking height positions provide useful selection details. The Vinland is an alternative when its stated 115-pound limit suits your 20 HP motor. Use support plates to reinforce existing bolt areas, not as motor mounts.
For transport, match the saver to your trailer and tilt or trim setup, checking stated fit requirements before purchase.


