How much to charge for pressure washing per square foot is typically $0.15-$0.40, with many residential flatwork jobs landing at $0.20-$0.30. Soft washing for roofs, siding, and delicate surfaces commonly reaches $0.30-$0.80 per square foot because chemicals, protection, access, and liability add labor beyond water application.
Key Facts and Quick Answer
- Concrete flatwork: Charge about $0.15-$0.30 per square foot, subject to a minimum service fee.
- House siding: Charge approximately $0.30-$0.50 per square foot, depending on height and material.
- Decks and fences: Charge roughly $0.35-$0.65 per square foot because wood requires slower, lower-pressure work.
- Roofs: Charge about $0.40-$0.80 per square foot for soft washing, chemical treatment, rinsing, and runoff control.
- Minimum job price: A practical residential minimum is often $150-$250, even when measured area is small.
- Quote basis: Calculate measured area, production time, labor, chemicals, travel, insurance, equipment, risk, and profit rather than multiplying square footage alone.
A square-foot price works best when the surface is broad, accessible, and reasonably uniform. A small walkway, steep roof, heavily stained restaurant pad, or three-story home can lose money under a low unit rate because setup and risk remain nearly unchanged while the measured area falls.
How Much Should You Charge by Surface?
Pressure washing prices depend first on the substrate and cleaning method. Durable concrete usually receives a faster, higher-pressure treatment, while wood, roofing, painted siding, and stucco require lower pressure, chemical dwell time, masking, and closer inspection.
| Surface or service | Typical charge per sq. ft. | Typical project total | Typical production time |
|---|---|---|---|
| Driveway or concrete patio | $0.15-$0.30 | $150-$350 | 1-3 hours |
| Sidewalk or walkway | $0.20-$0.35 | $100-$250 | 1-2 hours |
| Vinyl, brick, or stucco siding | $0.30-$0.50 | $300-$600 | 2-4 hours |
| Wood or composite deck | $0.35-$0.65 | $250-$500 | 2-5 hours |
| Fence cleaning | $0.35-$0.70 | $200-$600 | 2-5 hours |
| Roof soft washing | $0.40-$0.80 | $450-$950 | 3-6 hours |
These are typical U.S. residential planning ranges, not universal price rules. Local wages, insurance costs, climate, competition, water access, and permitting can move a quote substantially.
Why Concrete Usually Has the Lowest Unit Price
Concrete is generally the most efficient surface because it tolerates greater pressure, accepts surface cleaners, and allows long, predictable passes. A technician using a 20-inch surface cleaner may clean broad areas more consistently than with a wand, although oil, rust, chewing gum, and oxidation require separate treatment.
A plain 1,200-square-foot driveway at $0.20 per square foot produces only $240 before travel, setup, fuel, chemicals, insurance, labor, and payment processing. If the job consumes three hours door-to-door, the unit rate may be acceptable for a nearby route but inadequate as a standalone dispatch.
Why Roofs and Wood Require Higher Rates
Roof and wood cleaning prices include risk that square footage does not reveal. A roof may require fall protection, careful foot placement, gutter protection, landscaping rinses, sodium hypochlorite management, and a low-pressure rinse. Wood requires test patches and controlled pressure because aggressive cleaning can expose soft grain or create visible wand marks.
The price difference is therefore not simply a premium for a different nozzle. It compensates for slower production, chemical handling, protection work, inspection, and the potential cost of damage.
What Should a Per-Square-Foot Price Include?
A professional unit rate should include more than time spent spraying. The quote should account for the full service cycle:
- Customer communication and site assessment
- Travel, fuel, and vehicle depreciation
- Hose, pump, surface-cleaner, and nozzle setup
- Water use and chemical consumption
- Labor, payroll taxes, and workers’ compensation
- General liability and equipment insurance
- Plant, outlet, window, and door protection
- Wastewater containment or recovery where required
- Equipment maintenance and replacement
- Payment fees, estimating time, and business overhead
- Profit and a reserve for callbacks or minor damage
The U.S. Small Business Administration recommends separating business expenses into categories such as fixed costs, variable costs, and one-time costs when building a pricing model. That distinction matters because insurance and vehicle payments continue during slow weeks, while chemicals and labor rise with each job.
A Practical Pricing Formula
Use this formula for a defensible quote:
Price = direct labor + materials + travel + overhead allocation + risk allowance + target profit
For a square-foot price, divide the required revenue by the measured area:
Per-square-foot rate = required job revenue ÷ cleanable square footage
Example:
| Cost component | Example amount |
|---|---|
| Two technicians, 3 hours at $28 loaded labor | $168 |
| Fuel, water, and chemicals | $42 |
| Insurance, equipment, and overhead allocation | $85 |
| Access and surface-risk allowance | $35 |
| Target profit | $90 |
| Required job revenue | $420 |
| Measured area | 1,500 sq. ft. |
| Resulting rate | $0.28 per sq. ft. |
At $0.20 per square foot, the same 1,500-square-foot job generates $300 and may fail to cover the operator’s actual cost. At $0.30, it produces $450 and better matches the example’s required revenue.
Expert insight: The most common pricing mistake is dividing a desired hourly wage by spraying time alone. A three-hour wash may consume five hours of calendar capacity after driving, loading, setup, quoting, cleanup, and invoicing.
How Do Pressure Washing, Power Washing, and Soft Washing Differ?
Pressure washing uses pressurized water, power washing adds heated water, and soft washing combines low pressure with cleaning chemicals. The correct price follows the cleaning method and surface risk rather than the label used in a customer’s request.
| Method | Typical pressure | Water or chemical feature | Common applications |
|---|---|---|---|
| Cold-water pressure washing | 2,500-4,000 PSI | High-flow water | Concrete, brick, heavy dirt |
| Hot-water power washing | 2,000-4,000 PSI | Water up to about 200°F | Grease, oil, commercial pads |
| Soft washing | Usually under 500 PSI | Sodium hypochlorite and surfactant | Roofs, siding, algae |
| Manual or chemical-only treatment | Near-zero mechanical pressure | Brush or applied cleaner | Delicate materials, spot work |
PSI measures pressure, while gallons per minute measures water flow. In field production, GPM often determines how quickly loosened soil leaves the surface, so a machine with high PSI but insufficient flow may clean slowly.
When Should You Use Soft Washing?
Use soft washing when organic growth, paint, roofing granules, vinyl, or fragile coatings make mechanical force hazardous. Sodium hypochlorite can kill algae and mildew more effectively than pressure alone, but concentration, dwell time, ventilation, plant protection, and runoff control must be managed.
Soft washing is not automatically cheaper. The technician may spend more time mixing, protecting vegetation, rinsing, checking gutters, and returning equipment to its storage configuration. Those steps belong in the price.
How Do You Measure a Job Correctly?
Measure the surface that will actually be cleaned, not the property’s total lot area. Use a tape, laser measure, satellite measurement tool, or roof-measurement report, then verify unusual sections onsite.
- Divide the property into rectangles, triangles, and irregular sections.
- Multiply length by width for rectangular surfaces.
- Multiply base by height and divide by two for triangular sections.
- Subtract excluded areas such as doors, windows, planted beds, and permanent obstacles.
- Add separate rates for roofs, siding, decks, stairs, and heavily stained areas.
- Record height, slope, access, water supply, drainage, and surface condition.
- Photograph pre-existing cracks, failed caulk, loose paint, oxidation, and damaged screens.
- Apply the minimum charge if the calculated price falls below the service floor.
A 40-by-30-foot patio contains 1,200 square feet. At $0.25 per square foot, the measured price is $300, but a heavily stained surface may need pretreatment and a second pass that justifies a higher rate.
What Counts as Chargeable Area?
Chargeable area normally includes the surface receiving cleaning, including steps and vertical faces when they require separate labor. A contractor should state whether roof pricing uses plan-view area or actual sloped surface area because those measurements can differ.
Roofing software often reports the actual roof surface, while a simple aerial rectangle may understate it. Never quote a steep or complex roof from a rough footprint alone.
When Should You Use Hourly or Flat-Rate Pricing?
Use per-square-foot pricing for predictable surfaces and hourly or flat-rate pricing for uncertain work. A hybrid quote is often safest when the site contains multiple materials or unknown staining.
| Pricing model | Best use | Typical figure | Main weakness |
|---|---|---|---|
| Per square foot | Large, uniform flatwork | $0.15-$0.40 | Underprices difficult access |
| Hourly | Irregular or exploratory work | $60-$150 per hour | Customer cannot predict total |
| Flat project fee | Standard residential packages | $150-$800+ | Estimator absorbs surprises |
| Minimum plus unit rate | Small or mixed jobs | $150-$250 minimum | Requires clear scope |
A quote can state: “$250 minimum, including driveway cleaning up to 1,000 square feet, with additional concrete at $0.22 per square foot.” This protects the contractor from losing money on small jobs while giving the customer a measurable basis for additions.
How Should You Set a Minimum Charge?
Set the minimum by calculating the revenue needed to cover dispatch time. If travel, setup, cleaning, and administration consume two hours before washing begins, a $100 measured job is not economically equivalent to a $100 add-on near an existing route.
Typical minimums range from $150 to $250 for residential work and may exceed $300 in high-cost markets or for remote properties. Grouping a driveway, walkway, porch, and patio can make the visit worthwhile without hiding the cost from the customer.
Which Cost Factors Increase the Rate?
Square footage is only one pricing attribute. The following conditions commonly increase the quote:
| Cost driver | Typical adjustment or consequence | Why it matters |
|---|---|---|
| Two-story or difficult access | Add 20%-30% | Slower work and greater fall risk |
| No usable water source | Add $50-$200+ | Tank transport and refill time |
| Heavy oil or rust | Add $0.05-$0.20 per sq. ft. | Degreaser, heat, dwell, and multiple passes |
| Dense algae or moss | Add 10%-30% | Chemical application and repeat treatment |
| Wastewater recovery | Add $75-$300+ | Berms, vacuum recovery, disposal |
| Travel beyond service area | Add $25-$100+ | Fuel and lost production time |
Local stormwater requirements can change the economics. The U.S. Environmental Protection Agency’s Clean Water Act framework regulates pollutant discharges, while local municipal rules may restrict detergent, oil, and sediment entering storm drains. Contractors should check city or county requirements rather than assume rinse water is unrestricted.
Why Does Access Change the Price?
Access changes production rate. A technician carrying hoses around gates, moving vehicles, protecting delicate landscaping, or working from a lift cleans fewer square feet per hour than a technician operating a surface cleaner from an open driveway.
Height also raises exposure to broken seals, water intrusion, falls, and overspray. A 25% access premium is reasonable when the work genuinely consumes more time or requires additional safety equipment, but it should be explained rather than added arbitrarily.
What Does a Typical Quote Look Like?
A clear quote identifies the surface, measured area, method, inclusions, exclusions, and payment terms. It should not promise removal of permanent stains or imply that cleaning repairs cracks, failed coatings, or deteriorated mortar.
Example residential estimate:
| Line item | Quantity or basis | Amount |
|---|---|---|
| Concrete driveway | 1,200 sq. ft. at $0.24 | $288 |
| Front walkway | 180 sq. ft. at $0.28 | $50 |
| Oil pretreatment | Fixed allowance | $45 |
| Setup, plant protection, and rinse | Included | $0 |
| Minimum check | Not applicable | $0 |
| Estimated total | Before applicable tax | $383 |
The proposal should specify whether the customer supplies water and electricity, whether furniture must be moved, how access gates will be handled, and whether recurring organic growth is covered. Photos and written exclusions reduce disputes when a stain remains after reasonable cleaning.
Expert insight: Do not guarantee complete oil removal from porous concrete. Degreasing can lighten a stain, but hydrocarbons may have migrated below the surface, and repeated treatment can damage surrounding concrete before it produces a uniform appearance.
What Are the Alternatives to Pressure Washing?
Pressure washing is not the best treatment for every surface. Chemical treatment, manual scrubbing, steam cleaning, and abrasive blasting each solve different problems.
| Alternative | Typical price basis | Best for | Main limitation |
|---|---|---|---|
| Chemical-only treatment | $0.10-$0.30 per sq. ft. | Algae and light organic growth | Slow visual improvement |
| Manual brushing | $60-$150 per hour | Small delicate areas | High labor requirement |
| Hot-water cleaning | $0.25-$0.60 per sq. ft. | Grease and food residue | Fuel and equipment cost |
| Soda or abrasive blasting | $2-$6 per sq. ft. | Paint, rust, masonry restoration | Can damage ordinary siding or wood |
Chemical-only applications may be safer for fragile materials but may leave dust, embedded soil, and physical staining. Abrasive blasting can remove coatings that water cannot, yet it requires containment and can permanently alter the surface profile.
Common Mistakes That Reduce Profit or Cause Damage
Excess pressure can create repair claims faster than it creates revenue. A narrow nozzle held too close to concrete can etch lines or produce the circular “tiger stripe” effect associated with uneven passes.
Important safeguards include:
- Test a hidden area before cleaning wood, painted surfaces, or oxidized vinyl.
- Keep the nozzle moving and maintain a consistent distance.
- Use a surface cleaner rather than a wand for broad concrete whenever appropriate.
- Pre-wet and continuously rinse plants before chemical application.
- Protect exterior outlets, door thresholds, vents, and unsealed openings.
- Do not use roof-washing pressure intended for concrete.
- Treat rust, oil, and efflorescence as separate chemical problems.
- Photograph existing damage before connecting the hose.
- Confirm where runoff will travel before applying detergent.
- Avoid ladders when a ground-based extension or safer access method works.
Expert insight: Soft washing reduces impact damage, but concentrated chemicals can create more severe plant, paint, and metal damage than water. Low pressure is a method, not permission to ignore concentration, dwell time, or rinsing.
How Long Does a Pressure Washing Job Take?
A professional crew typically needs two to four hours for a 1,500-2,000-square-foot single-story exterior, including setup, washing, rinsing, and cleanup. A driveway may take one to three hours, while a roof or complex siding project may occupy half a day or longer.
| Job type | Active cleaning | Total onsite time | Main delay |
|---|---|---|---|
| 600 sq. ft. patio | 45-90 minutes | 1.5-2.5 hours | Furniture and stain treatment |
| 1,500 sq. ft. driveway | 1-2 hours | 2-3 hours | Oil, edges, and rinsing |
| 2,000 sq. ft. siding | 1.5-3 hours | 3-5 hours | Plant protection and height |
| 2,000 sq. ft. roof | 2-4 hours | 4-6 hours | Slope, chemical dwell, runoff |
Weather affects soft washing more than ordinary concrete cleaning. Rain can dilute chemicals, wind increases overspray, and cold temperatures slow reaction time or create unsafe conditions.
Regional Pricing and Profit Checks
A national range is only a starting point. Prices are commonly higher in major metropolitan areas, regions with expensive insurance, and markets where seasonal demand compresses scheduling capacity. Rural operators may charge less per square foot but more for travel.
Before publishing a rate card, compare three local inputs:
- Loaded labor cost, including payroll taxes and workers’ compensation.
- Average production rate for each surface, measured in square feet per labor hour.
- Total overhead per billable hour, including vehicles, equipment, insurance, software, and administration.
If a two-person crew costs $70 per labor hour and cleans 500 square feet per labor hour, labor alone equals $0.28 per square foot. Chemicals, travel, overhead, and profit must be added afterward. That calculation explains why a local contractor may need $0.40 for a difficult surface even when a national article quotes $0.20.
Frequently Asked Questions About how much to charge for pressure washing per square foot
Should I charge more for a very dirty driveway?
Yes. Heavy oil, rust, algae, gum, and embedded tire marks require pretreatment, dwell time, hot water, agitation, or multiple passes. Add a fixed treatment fee or approximately $0.05-$0.20 per square foot when the condition materially reduces production speed.
Is $0.20 per square foot enough for pressure washing?
$0.20 can work for accessible, lightly soiled concrete on a nearby route with efficient equipment. It may not cover a small standalone job, difficult access, chemical treatment, high labor costs, or wastewater recovery. Apply a minimum charge and verify the rate against loaded hourly costs.
How should I price a small walkway?
Use a minimum service price rather than multiplying a tiny area by a low unit rate. A 200-square-foot walkway at $0.25 produces only $50, so a $150-$200 minimum is more practical unless the walkway is an add-on to a nearby driveway or patio job.
Should roof cleaning use the roof’s footprint or surface area?
Use the actual cleanable roof surface when possible, and state the measurement method in the proposal. A sloped roof has more surface than its horizontal footprint. Complex hips, valleys, steep sections, and access limitations may justify a flat project price instead of a simple unit rate.
Do contractors charge separately for water?
Some contractors include ordinary hose access in the base price, while others add a fee when water must be hauled or a tank must be refilled. A no-water property commonly adds $50-$200 or more, depending on distance, tank capacity, refill time, and local water availability.
Can pressure washing remove every stain?
No. Cleaning can remove loose soil, algae, mildew, and some surface deposits, but it may not remove deep oil, rust migration, oxidation, paint failure, efflorescence, or permanent discoloration. A responsible quote identifies probable improvement rather than guaranteeing a uniform new-surface appearance.
Conclusion
How much to charge for pressure washing per square foot depends on surface, cleaning method, production speed, access, risk, and overhead. Use $0.15-$0.30 for ordinary concrete, $0.30-$0.65 for siding, decks, and fences, and $0.40-$0.80 for roof soft washing, then apply a practical minimum and verify the result against loaded labor and operating costs.


