A strong transmission jack for big trucks combines capacity suited to the drivetrain, a stable base, and a saddle that can position and secure the load; heavy-truck shops should start with truck-rated models rather than assume a car jack will fit. AFF 3180A leads this lineup with a 4,400-pound rating and stated use for transmissions, transfer cases, and differentials on trucks, buses, and construction equipment. The list also includes purpose-built Class 7 and 8 and diesel-truck options, plus low-profile jacks for limited clearance.
Capacity alone does not establish vehicle compatibility, and the listed vehicle type varies by model. Check the jack’s rating against the component, then confirm its minimum height, saddle adjustment, securing method, and working-height needs before choosing.
The AFF 3180A is the best overall choice here for big trucks because it combines a 4,400-pound capacity with stated suitability for truck, bus, and construction-equipment transmissions, transfer cases, and differentials. Its adjustable saddle tilts, and the supplied tilt figures are 15 degrees forward, 30 degrees rearward, and 12 degrees left or right. For Class 7 and 8 truck work, the OTC 1522A is a more specifically targeted alternative, rated at 2,000 pounds and supplied with an Eaton Fuller Roadranger adapter.
Our Top Picks
Best OverallRated for 4,400 pounds and described for truck, bus, and construction-equipment transmissions, transfer cases, and differentials; its saddle offers adjustable tilt.
View on Amazon
Best Class 7–8 FitExplicitly targets Class 7 and 8 trucks and includes an adapter for Eaton Fuller Roadranger transmissions; its low-profile design suits low-clearance trucks.
View on Amazon
Best Diesel-Truck MatchPurpose-built for removing, installing, and moving heavy-duty diesel truck transmissions, with a 1.5-ton rating, wide chassis, and two safety chains.
View on Amazon- Highest Capacity ESCO 10812
- Lowest Roll-Under Height OTC 5019A
Compare These Transmission Jacks for Truck Work
| # | Product | Dimensions | Load Capacity | Material | Compatible with Vehicle Type | Buy |
|---|---|---|---|---|---|---|
| 1 | 1. AFF 3180ABest Overall | 49 x 28 x 13 in | 4.4E+3 lb | Alloy Steel | Car | View on Amazon |
| 2 | 2. OTC 1522ABest Class 7–8 Fit | 12.5 x 27.5 x 12.5 in | 2000 lbs | Alloy Steel | Truck | View on Amazon |
| 3 | 3. Sunex 7752CBest Diesel-Truck Match | 60 x 38.25 x 24 in | 1.5 tons | Metal | Truck | View on Amazon |
| 4 | 4. ESCO 10812Highest Capacity | 43 x 35 x 26 in | 2.2 Ton | Alloy Steel | Trailer | View on Amazon |
| 5 | 5. OTC 5019ALowest Roll-Under Height | 54 x 35 x 12 in | 2200 lb | Metal | Truck | View on Amazon |
| 6 | 6. Stark USA 2-Ton JackHigh-capacity low-lift positioning | 46 x 26 x 13 in | 2 tons | Aluminum | ATV, Bus, Car, Sport Utility Vehicle… | View on Amazon |
| 7 | 7. AFF 3052AMedium-duty truck driveline work | 28 x 32 x 78 in | 1100 lb | Alloy Steel | Truck | View on Amazon |
| 8 | 8. OEMTOOLS 26842Telescoping high-lift positioning | 22 x 15.19 x 33.5 in | 1 ton | Alloy Steel | Car | View on Amazon |
| 9 | 9. Sunex 7793BHigh-reach foot-pedal lifting | 27.2 x 14.2 x 39.4 in | 1000 lb | Metal | Car | View on Amazon |
| 10 | 10. Maxority 2000 lb JackLow-profile 2,000-pound lifting | 40.16 x 22.44 x 8.66 in | 2000 lb | Carbon Steel, Cast Iron | Car | View on Amazon |
Detailed Reviews: Best Transmission Jack For Big Trucks

#1 · Best Overall
1. AFF 3180A
- Dimensions: 49 x 28 x 13 in
- Load Capacity: 4.4E+3 lb
- Material: Alloy Steel
- Compatible with Vehicle Type: Car
Best for: Heavy truck transmission handling.
Why it ranks #1: Rated for 4,400 pounds and described for truck, bus, and construction-equipment transmissions, transfer cases, and differentials; its saddle offers adjustable tilt.
A 4,400-pound capacity paired with a low-profile wishbone design gives the AFF 3180A clearance for large transmissions, transfer cases, and differentials on trucks, buses, and construction equipment. Its adjustable saddle and corner brackets help position those loads, while broad tilt adjustment supports alignment during removal and installation.
The wishbone design provides clearance for low-profile applications, and the 4,400-pound rating suits the heavy transmissions and other driveline components named in the product description. Saddle tilt and adjustable corner brackets help position a load, with specified tilt ranges of 15 degrees forward, 30 degrees rearward, and 12 degrees to either side. A 32-inch handle rotates around the pump, giving the operator more flexibility to work around the jack. Four grab handles and industrial-grade casters support positioning and transport.
- 4,400-pound load capacity
- Wishbone design for low-profile clearance
- Adjustable saddle and corner brackets
- 32-inch handle rotates 360 degrees around the pump
- Its 4,400-pound capacity is below the Stark USA 2-ton jack's stated 4,409-pound rating.
Skip it if you need a stated truck-compatible rating above 4,400 pounds; the Stark USA 2-ton jack lists 4,409 pounds.
For shops handling large truck, bus, or construction-equipment driveline components, the AFF offers low-profile access and adjustable positioning. Its listed capacity is 4,400 pounds, so keep the load within that rating.
Full product details
| Brand | AFF |
|---|---|
| Color | Red |
| Compatible with Vehicle Type | Car |
| Included Components | 1 jack |
| Item Dimensions | 49 x 28 x 13 inches |
| Load Capacity | 4.4E+3 pounds |
| Manufacturer | SureWerx |
| Part Number | AFF-3180A |
| Manufacturer Warranty Description | 1 year |
| Material | Alloy Steel |
| Model Number | AFF-3180A |
| Style Name | Heavy Duty |
Listed on Amazon as: AFF Manual Hydraulic Low Profile Transmission Jack – 4,400 lbs Capacity
View on Amazon
#2 · Best Class 7–8 Fit
2. OTC 1522A
- Dimensions: 12.5 x 27.5 x 12.5 in
- Load Capacity: 2000 lbs
- Material: Alloy Steel
- Compatible with Vehicle Type: Truck
Best for: Class 7 and 8 truck service.
Why it ranks #2: Explicitly targets Class 7 and 8 trucks and includes an adapter for Eaton Fuller Roadranger transmissions; its low-profile design suits low-clearance trucks.
A 2,000-pound rating and included adapter make the OTC 1522A a purpose-specific option for heavy transmissions, including Eaton Fuller Roadranger units used in many Class 7 and 8 trucks. Its low-profile design reaches beneath low-clearance trucks, while overload and hydraulic bypass safeguards address operation at the jack’s limits.
The included adapter is specified for the Eaton Fuller Roadranger transmissions named in the product information, helping match the jack to common Class 7 and 8 truck drivetrains. Its low profile supports access beneath low-clearance trucks for clutch work. An overload feature prevents use beyond rated capacity, and a safety bypass protects the hydraulic cylinder from damage. The 2,000-pound rating sets the load boundary; the jack’s stated truck compatibility makes it a focused heavy-truck service choice.
- 2,000-pound capacity
- Adapter included for Eaton Fuller Roadranger transmissions
- Low-profile access for low-clearance trucks
- Overload feature and hydraulic safety bypass
- Its 2,000-pound capacity is less than half the AFF 3180A's 4,400-pound rating.
Skip it if you handle loads above 2,000 pounds; the AFF 3180A is rated for 4,400 pounds and suits larger driveline components.
For Class 7 and 8 truck shops servicing compatible heavy transmissions, the OTC combines a low profile with a specific included adapter. Confirm the load stays within its 2,000-pound rated capacity.
Full product details
| Brand | OTC |
|---|---|
| Color | Silver |
| Compatible with Vehicle Type | Truck |
| Included Components | Unit^Instruction Guide |
| Item Dimensions | 12.5 x 27.5 x 12.5 inches |
| Load Capacity | 2000 lbs |
| Manufacturer | OTC |
| Part Number | 1522A |
| Manufacturer Warranty Description | 1 year manufacturer |
| Material | Alloy Steel |
| Model Number | 1522A |
| Style Name | Hydraulic |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov |
Listed on Amazon as: OTC 1522A 2,000 lb. Heavy-Duty, Low-Lift Transmission Jack for Class 7 & 8
View on Amazon
#3 · Best Diesel-Truck Match
3. Sunex 7752C
- Dimensions: 60 x 38.25 x 24 in
- Load Capacity: 1.5 tons
- Material: Metal
- Compatible with Vehicle Type: Truck
Best for: Heavy-duty diesel truck work.
Why it ranks #3: Purpose-built for removing, installing, and moving heavy-duty diesel truck transmissions, with a 1.5-ton rating, wide chassis, and two safety chains.
A 1.5-ton capacity and wide chassis make the Sunex 7752C a truck-focused option for removing, installing, and moving heavy-duty diesel transmissions. Its universal adjustable saddle has four brackets for matching transmission-pan configurations, and two safety chains with adjustment hardware help secure the load during handling.
The 1.5-ton rating is paired with a wide chassis that supports load distribution and stability during heavy-duty diesel transmission work. Four adjustable saddle brackets can be lined up with transmission-pan configurations, helping adapt the support surface to the load. Two safety chains and adjustment hardware secure the transmission to the saddle during removal, installation, and movement. At 300 pounds and 60 inches long, the listed dimensions and weight are useful practical considerations for positioning and storing this truck jack.
- 1.5-ton capacity
- Wide chassis for load distribution and stability
- Four adjustable saddle brackets
- Two safety chains with adjustment hardware
- At 300 pounds, it is heavier than the AFF 3052A's listed 172 pounds.
Skip it if you prioritize a lighter listed jack; the AFF 3052A weighs 172 pounds and is intended for medium-duty transmissions.
The Sunex 7752C suits shops moving heavy-duty diesel truck transmissions that benefit from an adjustable four-bracket saddle and two chains. Its 1.5-ton rating and 300-pound listed weight define important handling limits.
Full product details
| Brand | Sunex Tools |
|---|---|
| Color | Red |
| Compatible with Vehicle Type | Truck |
| Included Components | 1 Truck transmission jack |
| Item Dimensions | 60 x 38.25 x 24 inches |
| Item Weight | 300 pounds |
| Load Capacity | 1.5 tons |
| Manufacturer | Sunex |
| Part Number | SUN7752C |
| Manufacturer Warranty Description | Manufacturer Warranty |
| Material | Metal |
| Model Number | SUN7752C |
| Style Name | 1-1/2 Ton |
Listed on Amazon as: SUNEX TOOLS 7752C 1-1/2-Ton Truck Transmission Jack
View on Amazon
#4 · Highest Capacity
4. ESCO 10812
- Dimensions: 43 x 35 x 26 in
- Load Capacity: 2.2 Ton
- Material: Alloy Steel
- Compatible with Vehicle Type: Trailer
Best for: Heavy loads with sealed hydraulics.
Why it ranks #4: Its 4,400-pound capacity and wide chassis target heavy-duty transmissions, while an adjustable universal saddle, brackets, and chain sling help secure loads.
A 4,400-pound capacity pairs with a sealed hydraulic unit on the ESCO 10812, giving heavy-duty transmission work a substantial rated load limit while keeping the piston and cylinder clean of debris. Its universal saddle, brackets, and chain sling support adaptable load positioning, and the pump handle rotates 360 degrees.
The 2.2-ton, 4,400-pound rating makes this jack suitable for loads within its stated heavy-duty capacity. A fully adjustable universal saddle, brackets, and chain sling support positioning and restraint, while the 360-degree pump handle allows operation from different positions. The sealed hydraulic unit keeps the piston and cylinder clean and free of debris, and the overload system guards against use beyond the rated limit. Four swiveling casters support rolling the jack into place.
- 4,400-pound capacity
- Fully adjustable universal saddle, brackets, and chain sling
- 360-degree rotatable pump handle
- Sealed hydraulic unit keeps piston and cylinder clean
- Its listed compatible vehicle type is trailer, not truck.
Skip it if you need a jack explicitly listed for trucks; the OTC 1522A is compatible with trucks and rated for 2,000 pounds.
The ESCO suits buyers handling heavy transmissions who value a 4,400-pound rating, adjustable restraint, and sealed hydraulics. Its listed compatible vehicle type is trailer, so that fit detail matters for truck service.
Full product details
| Brand | ESCO |
|---|---|
| Color | Yellow, Black, Silver, Red |
| Compatible with Vehicle Type | Trailer |
| Included Components | 10812 |
| Item Dimensions | 43 x 35 x 26 inches |
| Item Weight | 230 pounds |
| Load Capacity | 2.2 Ton |
| Manufacturer | ESCO |
| Part Number | 10812 |
| Manufacturer Warranty Description | 1 year |
| Material | Alloy Steel |
| Model Number | 10812 |
| Style Name | Hydraulic |
Listed on Amazon as: Esco 10812 2.2 Ton Heavy Duty Transmission Jack, 4,400 lb Capacity, Adjustable 10"–35" Lift – Yellow
View on Amazon
#5 · Lowest Roll-Under Height
5. OTC 5019A
- Dimensions: 54 x 35 x 12 in
- Load Capacity: 2200 lb
- Material: Metal
- Compatible with Vehicle Type: Truck
Best for: Low-clearance truck service.
Why it ranks #5: The 2,200-pound truck jack has an 81⁄4-inch roll-under height and swiveling pump handle, useful where low clearance and restricted workspace coincide.
An 81⁄4-inch roll-under height is the OTC 5019A’s defining advantage, helping it reach beneath modern aerodynamic trucks with limited ground clearance. Its swiveling pump handle also gives operators room to work in restricted spaces, while the 2,200-pound capacity and angle-adjustable mounting plate support transmission positioning.
The 81⁄4-inch starting height addresses trucks with low ground clearance, while the swiveling pump handle allows operation where a fixed handle needs more clearance. A fast-acting pump raises the lifting arm quickly, supporting a more direct lift workflow. The mounting plate adjusts its angle with a wrench, letting the operator make positioning changes at the load. At 2,200 pounds, its capacity is suited to loads that remain within that limit; it is a low-lift truck jack, not the highest-capacity option here.
- 81⁄4-inch roll-under height
- Swiveling pump handle for restricted spaces
- Fast-acting lifting-arm pump
- Angle-adjustable mounting plate
- Its 2,200-pound capacity is lower than the AFF 3180A's 4,400-pound rating.
Skip it if you need capacity above 2,200 pounds for a heavier transmission; the AFF 3180A is rated for 4,400 pounds.
Choose the OTC 5019A for truck work where low ground clearance and cramped pump access are central concerns. Its 2,200-pound limit and wrench-adjusted plate make load weight and positioning needs important boundaries.
Full product details
| Brand | OTC |
|---|---|
| Color | Blue |
| Compatible with Vehicle Type | Truck |
| Included Components | Transmission Jack |
| Item Dimensions | 54 x 35 x 12 inches |
| Item Weight | 280 pounds |
| Load Capacity | 2200 pound |
| Manufacturer | OTC |
| Part Number | 5019A |
| Manufacturer Warranty Description | Manufacturer Warranty |
| Material | Metal |
| Model Number | 5019A |
| Style Name | Jack |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 Warning for California Consumers WARNING: Reproductive Harm – www.P65Warnings.ca.gov |
Listed on Amazon as: OTC 5019A 2,200 lb. Low-Lift Transmission Jack with Premounted Adapter
View on Amazon
#6
6. Stark USA 2-Ton Jack
- Dimensions: 46 x 26 x 13 in
- Load Capacity: 2 tons
- Material: Aluminum
- Compatible with Vehicle Type: ATV, Bus, Car, Sport Utility Vehicle…
Best for: High-capacity low-lift positioning.
Why it ranks #6: Rated at 4,409 pounds and listed for trucks, it includes an Eaton, Fuller, and Road Ranger adapter; its stated fit also includes cars and light trucks.
A 4,409-pound rated capacity gives the Stark USA jack substantial load headroom, while its 8.27-inch minimum height supports roll-under access. The universal mounting head and included adapter plate for Eaton, Fuller, and Road Ranger transmissions help make it relevant to both automotive work and compatible truck drivetrains.
The 8.27-inch minimum lifting height supports access beneath low-clearance vehicles, and the 37.8-inch maximum height defines its lifting range. A universal mounting head and the included adapter plate for Eaton, Fuller, and Road Ranger transmissions support positioning with those named drivetrains. The pump handle rotates 360 degrees to improve operator access, while 3.5-inch ball-bearing swivel casters help move the 308.7-pound jack into place. Its 4,409-pound rating is a firm load limit.
- 4,409-pound rated capacity
- 8.27-inch minimum lifting height
- Adapter plate for Eaton, Fuller, and Road Ranger transmissions
- 360-degree pump handle and swivel casters
- Its stated maximum lifting height is 37.8 inches, below the OEMTOOLS 26842's 76 inches.
Skip it if you need a stated lifting height above 37.8 inches; the OEMTOOLS 26842 reaches 76 inches.
The Stark USA suits buyers needing a low-lift jack with a high stated capacity and an adapter for named truck transmissions. Check both the 37.8-inch maximum height and 4,409-pound load boundary against the job.
Full product details
| Brand | Stark USA |
|---|---|
| Color | Blue |
| Compatible with Vehicle Type | ATV, Bus, Car, Sport Utility Vehicle, Tractor, Trailer, Truck, UTV |
| Included Components | Hydraulic Lift Floor Jack, Manual |
| Item Dimensions | 46 x 26 x 13 inches |
| Item Weight | 308.7 pounds |
| Load Capacity | 2 tons |
| Manufacturer | Stark USA |
| Part Number | 56026 |
| Manufacturer Warranty Description | 90 days |
| Material | Aluminum |
| Model Number | JACK TRANSMISSION 2 TON LOW-LIFT, SE |
| Style Name | TransmissionFloor Jack |

#7
7. AFF 3052A
- Dimensions: 28 x 32 x 78 in
- Load Capacity: 1100 lb
- Material: Alloy Steel
- Compatible with Vehicle Type: Truck
Best for: Medium-duty truck driveline work.
Why it ranks #7: Designed for medium-duty truck transmissions, transfer cases, and differentials, but its 1,100-pound capacity makes it less suited to heavier truck components.
A two-stage air-assist system combines a hydraulic dual pump with a dedicated air motor to lift the AFF 3052A’s 1,100-pound rated load. That setup suits medium-duty truck transmissions, transfer cases, and differentials, while a foot pedal lets the operator pump and release with hands free for positioning.
The air motor and dual-pump hydraulic system support fast lifting, while the foot-operated pump and release leave the operator’s hands available to guide or position a component. A wide base supports stability, and the adjustable saddle includes corner brackets and a safety chain to help secure the load. The 1,100-pound rating makes this a medium-duty choice rather than a solution for heavier truck transmissions. Its telescoping design extends the jack for working at a range of heights.
- Two-stage air-assist telescoping lift
- Hydraulic dual-pump system
- Foot-pedal pump and release
- Wide base, adjustable saddle, and safety chain
- Its 1,100-pound capacity is limited for heavier truck transmissions.
Skip it if you handle transmissions above 1,100 pounds; the OTC 1522A is rated for 2,000 pounds and targets Class 7 and 8 trucks.
The AFF 3052A fits medium-duty truck shops that value hands-free pumping, air-assisted lifting, and a securing chain. Keep the 1,100-pound capacity in view when selecting it for transmission or driveline work.
Full product details
| Brand | AFF |
|---|---|
| Color | Red |
| Compatible with Vehicle Type | Truck |
| Included Components | Transmission Jack |
| Item Dimensions | 28 x 32 x 78 inches |
| Item Weight | 172 pounds |
| Load Capacity | 1100 pound |
| Manufacturer | SureWerx |
| Part Number | 3052A |
| Material | Alloy Steel |
| Model Number | 3052A |
| Style Name | Air Assist |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: This product can expose you to chemicals including lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov |
Listed on Amazon as: AFF Telescoping Transmission Jack – Truck Transmission Floor Jack with Universal Head and Wide Base (Multiple Weight Capacities)
View on Amazon
#8
8. OEMTOOLS 26842
- Dimensions: 22 x 15.19 x 33.5 in
- Load Capacity: 1 ton
- Material: Alloy Steel
- Compatible with Vehicle Type: Car
Best for: Telescoping high-lift positioning.
Why it ranks #8: The 1-ton, two-stage telescoping jack offers a 37.5-to-76-inch high-lift range, but its listed compatible vehicle type is car rather than truck.
A two-stage system reaches from 37.5 to 76 inches, giving the OEMTOOLS 26842 a broad height range for transmission installation and removal. Its foot-pedal control supports hands-free positioning, while the 1-ton capacity sets its load limit. This is the high-reach choice among the listed jacks, not the highest-capacity truck option.
The two-stage hydraulic system provides controlled lifting and lowering across the stated 37.5-to-76-inch range, supporting precise positioning during installation. Foot-pedal control allows operation without using hands on the pump, while the telescoping design supplies the high reach identified in the product title. Its 1-ton capacity is the critical boundary for load selection. The listed compatible vehicle type is car, so buyers choosing a jack specifically for truck service should account for that stated fit.
- Two-stage hydraulic lift
- 37.5-to-76-inch height range
- Foot-pedal control for positioning
- 1-ton rated capacity
- Its listed compatible vehicle type is car, not truck.
Skip it if you need a jack explicitly listed for trucks; the OTC 5019A is compatible with trucks and rated for 2,200 pounds.
Choose the OEMTOOLS for high-reach positioning when its 1-ton capacity and 37.5-to-76-inch range match the job. Its listed vehicle compatibility is car, a relevant boundary for a truck-focused roundup.
Full product details
| Brand | OEMTOOLS |
|---|---|
| Color | Green |
| Compatible with Vehicle Type | Car |
| Included Components | 1 Ton 2 Stage Telescoping Transmission Jack |
| Item Dimensions | 22 x 15.19 x 33.5 inches |
| Item Weight | 193 pounds |
| Load Capacity | 1 ton |
| Manufacturer | OEMTOOLS |
| Part Number | 26842 |
| Manufacturer Warranty Description | OEMTOOLS 1 Year Limited |
| Material | Alloy Steel |
| Model Number | 26842 |
| Style Name | Telescoping, 1 Ton 2 Stage |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov |
Listed on Amazon as: OEMTOOLS 26842 1-Ton Transmission Jack with High Lift 37.5"–76"
View on Amazon
#9
9. Sunex 7793B
- Dimensions: 27.2 x 14.2 x 39.4 in
- Load Capacity: 1000 lb
- Material: Metal
- Compatible with Vehicle Type: Car
Best for: High-reach foot-pedal lifting.
Why it ranks #9: Its telescoping design reaches 74 inches and includes a tilt saddle and tie-down strap, but the listed compatible vehicle type is car.
A 74-inch maximum height gives the Sunex 7793B reach for elevated transmission work, while its foot-activated pump raises the telescoping rams without occupying the operator’s hands. A tilt saddle and nylon tie-down strap add load-positioning and restraint features, with a 1,000-pound capacity defining its working range.
The two telescoping stages extend to a maximum height of 74 inches, supporting work that needs more reach than a low-lift jack provides. The foot pedal raises the rams hands-free, which can leave both hands available to manage positioning. Its tilt saddle uses four adjustable fingers, and the nylon strap secures the transmission to the saddle. Lowered rams allow transfer from the jack to a work table, though the 1,000-pound rating limits the loads it can handle.
- 74-inch maximum lifting height
- Hands-free foot-pedal pump
- Tilt saddle with four adjustable fingers
- Nylon strap secures the load
- Its 1,000-pound capacity is limited for heavy truck transmissions.
Skip it if you handle heavy truck transmissions above 1,000 pounds; the Sunex 7752C is rated for 1.5 tons.
This Sunex suits service work that needs telescoping reach, foot-pedal operation, and a strap-secured load. Its 1,000-pound limit makes load weight a key boundary, particularly when working with heavy truck transmissions.
Full product details
| Brand | Sunex Tools |
|---|---|
| Color | Black |
| Compatible with Vehicle Type | Car |
| Included Components | Sunex Tools 7793B 1,000 lb Telescopic Transmission Jack, Hydraulic, Foot Pump Operated, Tilt Saddle with Chain Tie-Down, 74.2 in Max Height |
| Item Dimensions | 27.2 x 14.2 x 39.4 inches |
| Item Weight | 163.4 pounds |
| Load Capacity | 1000 pounds |
| Manufacturer | Sunex International |
| Part Number | 7793B |
| Manufacturer Warranty Description | 1 year |
| Material | Metal |
| Model Number | 7793B |
| Style Name | 1/2-Ton Telescopic Trans-Jack |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: This product can expose you to chemicals including nickel (metallic) which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov |
Listed on Amazon as: Sunex Tools 7793B 1,000 lb Telescopic Transmission Jack, Hydraulic, Foot Pump Operated, Tilt Saddle with Chain Tie-Down, 74.2 in Max Height
View on Amazon
#10
10. Maxority 2000 lb Jack
- Dimensions: 40.16 x 22.44 x 8.66 in
- Load Capacity: 2000 lb
- Material: Carbon Steel, Cast Iron
- Compatible with Vehicle Type: Car
Best for: Low-profile 2,000-pound lifting.
Why it ranks #10: The 2,000-pound low-profile telescoping jack lists car compatibility, not truck use, so it is the weakest match for a big-truck transmission job.
A low starting height helps the Maxority MAX0702-1 slide beneath vehicles with limited ground clearance, while its 2,000-pound rating covers loads within that capacity. The telescoping hydraulic lift provides an extended height range for positioning, and 360-degree swivel casters support maneuvering the jack around a service area.
The low-profile floor design is specified for access beneath vehicles with limited ground clearance, including vehicles on lifts or jack stands. Its multi-stage telescoping hydraulic system provides an extended height range, supporting careful alignment during installation and controlled lowering. Swivel casters that rotate 360 degrees make repositioning more manageable around the work area. The listed compatible vehicle type is car, so truck buyers should weigh that stated compatibility alongside the 2,000-pound capacity before choosing it for truck service.
- Low starting height for limited-clearance access
- Multi-stage telescoping hydraulic lift
- 2,000-pound capacity
- 360-degree swivel casters
- Its listed compatible vehicle type is car, not truck.
Skip it if you need a jack explicitly listed for trucks; the OTC 1522A is compatible with trucks and rated for 2,000 pounds.
The Maxority fits buyers seeking a low-profile, telescoping jack for car service with a 2,000-pound capacity. Its listed vehicle compatibility is car, so that specification is an important boundary for truck-focused work.
Full product details
| Brand | Maxority |
|---|---|
| Compatible with Vehicle Type | Car |
| Included Components | Transmission jack |
| Item Dimensions | 40.16 x 22.44 x 8.66 inches |
| Load Capacity | 2000 Pounds |
| Manufacturer | Maxority |
| Part Number | MAX0702-1 |
| Manufacturer Warranty Description | 90 Days Limited Warranty |
| Material | Carbon Steel, Cast Iron |
| Model Number | MAX0702-1 |
Listed on Amazon as: 2000 lb Adjustable Hydraulic Transmission Jack – Low Profile Telescoping Floor Lift with 360° Swivel Casters, Heavy-Duty Steel Construction
View on AmazonAvoid a capacity-and-fit mismatch
A stated capacity does not by itself confirm that a jack fits a particular truck transmission or its underbody clearance. The clearest compatibility evidence in this selection is specific: the OTC 1522A names Class 7 and 8 trucks and includes an Eaton Fuller Roadranger adapter, while the Sunex 7752C is described for heavy-duty diesel truck transmissions. The AFF 3180A names trucks, buses, and construction equipment, but its listed compatible vehicle type says car, so buyers should verify application details rather than rely on one field alone.
There is also a rating trap: the AFF 3052A is described for medium-duty truck components but is rated at 1,100 pounds. Compare the component’s required support with the jack’s rating and confirm the transmission or adapter fit before work.
A jack that rolls under the truck but cannot support or locate the specific unit is not an adequate match.
Plan for securing and controlling the load
A transmission jack’s saddle and restraint arrangement matter because positioning and securing are separate tasks. The Sunex 7752C provides an adjustable saddle with four brackets and two safety chains; the ESCO 10812 lists an adjustable universal saddle, brackets, and chain sling. The AFF 3180A offers saddle tilt and adjustable corner brackets, while the OTC 5019A has an angle-adjustable mounting plate.
Those features address different needs: a chain or sling helps retain a load, while saddle adjustment helps align its support points. Do not treat any listed restraint as proof that a particular transmission is safely secured; check the manufacturer’s instructions and the load’s fit.
Telescoping designs also create a trade-off: models such as the Sunex 7793B and OEMTOOLS 26842 provide high lift, but their listed vehicle type is car. For truck work, confirm reach and clearance alongside the restraint system.
How to Choose a Big-Truck Transmission Jack
Capacity and truck-duty match
Look for a capacity that meets the supported component’s requirements and a product description that fits your truck duty. This selection ranges from 1,000 pounds for the Sunex 7793B to 4,409 pounds for the Stark USA 2-Ton Jack; the AFF 3180A and ESCO 10812 each list 4,400 pounds. Between those ends, the Sunex 7752C is rated at 1.5 tons, while the OTC 1522A is rated at 2,000 pounds and specifically targets Class 7 and 8 trucks.
The highest listed rating is not automatically the best match: a buyer working with a named heavy-truck transmission may favour the OTC, while a buyer needing the largest stated capacity among truck-suitable choices may prefer the AFF or ESCO. Verify the actual component and application.
Roll-under clearance and working height
Check both the minimum height needed to get under the truck and the lift height needed to handle the transmission. The OTC 5019A has an 81⁄4-inch roll-under height, and the Stark USA 2-Ton Jack lists a minimum lifting height of 8.27 inches. For high lift, the Sunex 7793B reaches 74 inches, while OEMTOOLS 26842 lists a range of 37.5 to 76 inches; the AFF 3180A’s supplied dimensions are 49 by 28 by 13 inches, not a stated minimum lift height.
Buyers working beneath low-clearance trucks should favour a model with a specified low starting height. Those who need an elevated transfer position should compare maximum height, but should also verify truck compatibility rather than infer it from reach.
Saddle adjustment and load retention
Choose a saddle and restraint arrangement that can support the transmission’s shape and keep it positioned during handling. The Sunex 7752C combines four adjustable brackets with two safety chains; ESCO 10812 lists a universal saddle, brackets, and chain sling. AFF 3180A has adjustable corner brackets and a tilting saddle, with verified tilt figures of 15 degrees forward, 30 degrees rearward, and 12 degrees to either side.
OTC 1522A includes an adapter for Eaton Fuller Roadranger transmissions, and OTC 5019A uses an angle-adjustable mounting plate. A buyer handling varied pan configurations may favour the adjustable-bracket models.
Someone servicing the named Eaton Fuller family should consider the OTC adapter, while a job needing extra angle positioning may suit the AFF. Confirm the saddle setup for the actual transmission.
Which Transmission Jack Should You Choose?
For broad heavy-truck use, choose the AFF 3180A: its 4,400-pound rating and stated truck, bus, and construction-equipment applications make it the strongest all-around fit in this group. For Class 7 or 8 work involving Eaton Fuller Roadranger transmissions, the OTC 1522A is the more specifically matched option, with its included adapter and low-profile design. For heavy-duty diesel truck transmissions and a wide chassis with two safety chains, consider the Sunex 7752C.
Choose the ESCO 10812 if its 4,400-pound capacity and adjustable saddle with chain sling suit the job. Where low ground clearance is the key constraint, the OTC 5019A offers an 81⁄4-inch roll-under height.
Match capacity, clearance, saddle, and restraint to the truck and transmission before buying.
Related Buying Guides
- Best Semi Truck Transmission Jack
- Best Big Truck Tires
- Best Transmission Jack For Car Lift
- Best Big Rims For Trucks
- Best Jacks For Trucks
- Best Tire Tools For Big Trucks
Frequently Asked Questions
How do I determine the transmission jack capacity needed for my truck?
Choose a jack rated to support the transmission and any attached components being handled, with capacity appropriate for the job. Check the transmission’s weight rather than estimating from the truck’s size, and account for transfer cases or other components if they will be supported together. The AFF 3180A is rated for 4,400 pounds; the OTC 1522A is rated for 2,000 pounds.
How can I check whether a transmission jack will fit beneath my truck?
Measure the available clearance beneath the truck and compare it with the jack’s roll-under height, including the saddle or adapter as relevant. Also check that the jack can reach the required lifting position. The OTC 5019A has a stated roll-under height of 81⁄4 inches; verify that this suits your truck’s clearance.
What additional support should I use when removing a truck transmission?
Use appropriate vehicle supports and secure the transmission with the jack’s restraint system, such as a chain or tie-down where supplied. Keep the load stable and follow the vehicle and jack manufacturers’ procedures; a transmission jack should not replace proper support for the vehicle. Check that the saddle and restraints suit the transmission before removal.
What should I compare besides rated capacity?
Compare roll-under clearance, lift range, saddle adjustability, and the way the transmission is secured. These features affect whether a jack can reach the work area and hold the load in a controlled position. For example, the OTC 5019A is listed with an 81⁄4-inch roll-under height, while some options specify tilt saddles or chain tie-downs.
When is a model-specific adapter useful?
A model-specific adapter can be useful when it matches the transmission you plan to service. The OTC 1522A is supplied with an Eaton Fuller Roadranger adapter and is specifically targeted to Class 7 and 8 work. Confirm compatibility with your transmission and the jack’s instructions before relying on an adapter.
Final Words
For broad heavy-truck work, the AFF 3180A is the strongest all-around choice in this group: its 4,400-pound rating and stated suitability for truck, bus, and construction-equipment transmissions, transfer cases, and differentials cover a wide range of tasks. Choose the OTC 1522A instead for Class 7 or 8 work involving Eaton Fuller Roadranger transmissions. Before deciding, match capacity, under-truck clearance, saddle adjustment, and restraint to the specific job.


