Best Step Pads For Nerf Bars: Compare Fit, Kits, and Clips

Best Step Pads For Nerf Bars

A strong step-pad replacement matches your nerf bar’s tube diameter and mounting pattern, then supplies the pads and clips needed for the repair. The Iexcauw four-pack is a practical starting point for owners with 3-inch round bars and a five-pin layout; it includes four 21-by-3-inch pads, 24 pins, and a rubber mallet. This roundup compares ten options, from multi-pad kits for common 3-inch round tubes to exact-series replacements for Westin Signature 3 bars and Dee Zee pads.

The key caveat is that “3-inch round” alone does not confirm fit: pad dimensions and pin spacing also matter, and some products are expressly limited to a particular bar series. Measure an existing pad and verify its holes before ordering.

Iexcauw 4-Pack is the Best Overall choice for shoppers whose bars match its stated 3-inch round, five-pin configuration. It supplies four 21-by-3-inch pads, 24 pins, and a rubber mallet, while its reinforced polymer design is described as resisting cracking, fading, corrosion, and UV damage. Check your existing pad’s dimensions and hole spacing first: the listing says this kit is not universal, so a different tube size or mounting layout calls for another option.

Our Top Picks

Iexcauw NBS4PBest Overall

Iexcauw NBS4P

Four 21-by-3-inch pads, 24 pins, a rubber mallet, and a reinforced design make this a well-equipped kit for matching 3-inch round, five-pin bars.

View on Amazon
Generic 21-Inch Pad KitBest Tool Bundle

Generic 21-Inch Pad Kit

The four-pad kit includes 25 pins, a rubber hammer, and a drill bit; its listed five-hole spacing helps buyers verify a close match.

View on Amazon
XNGQUEY 0001Best Spacing Detail

XNGQUEY 0001

This four-pack specifies 21-by-3-inch pads and pin intervals of 3-5/8, 5-5/8, 6-3/8, and 3-5/8 inches, plus 24 clips.

View on Amazon

Compare the Step Pad Options

#ProductdimensionsWeightMaterialCompatible with Vehicle TypeBuy
1
Iexcauw NBS4P1. Iexcauw NBS4PBest Overall
21 x 3 x 3 in—PlasticThis pad is NOT universal. It is specifically…View on Amazon
221 x 3 x 3 in2.4 lbAcrylonitrile Butadiene Styrene (ABS)3-5/8", 6-3/8", 5-5/8", 3-5/8" from one end…View on Amazon
3
XNGQUEY 00013. XNGQUEY 0001Best Spacing Detail
21 x 3 x 2 in1.4 lbPlastic3" Round Step Pads, Truck, nerf bar…View on Amazon
4
RuggedXL STP11264. RuggedXL STP1126Best Clip Supply
21 x 3 x 2 in—Plastic3" Round Step Pads, This product is a…View on Amazon
5
MEFDUK 5-Hole Pads5. MEFDUK 5-Hole PadsWeather-resistant four-pad set
4.31 x 5.12 x 22.44 in1.5 kgMetal, Plasticfit for 3" Round Step PadsView on Amazon
6
JUFZQO Upgraded Pads6. JUFZQO Upgraded PadsTemperature-resistant polymer pads
21 x 3 x 2 in0.7 kgPlastic3" Round Step PadsView on Amazon
7
Iexcauw NBS2P7. Iexcauw NBS2PBest Two-Pack
21 x 3 x 3 in0.7 kgPlasticVerify tube diameter (3") & hole spacing…View on Amazon
8
USHDHDID 25-00018. USHDHDID 25-0001Westin Signature 3 two-pack
20 x 4 x 2.7 in—PlasticVanView on Amazon
9
Westin 25-00019. Westin 25-0001Signature 3 single-pad replacement
—11.2 oz——View on Amazon
10
Dee Zee DZ4INCHECKS10. Dee Zee DZ4INCHECKSDee Zee four-bar step set
28 x 6 x 6 in2 lbAluminumTruckView on Amazon

Detailed Reviews: Best Step Pads For Nerf Bars

Iexcauw NBS4P

#1 · Best Overall

1. Iexcauw NBS4P

  • dimensions: 21 x 3 x 3 in
  • Material: Plastic
  • Compatible with Vehicle Type: This pad is NOT universal. It is specifically…

Best for: Four-pad installation kit.

Why it ranks #1: Four 21-by-3-inch pads, 24 pins, a rubber mallet, and a reinforced design make this a well-equipped kit for matching 3-inch round, five-pin bars.

Four 21-by-3-inch pads make this Iexcauw set the useful choice when a whole set of steps needs refreshing. Its reinforced polymer backs are intended to resist cracking under hard stepping, while the included rubber mallet and 24 pins give the installation a supplied tool and mounting hardware.

The grid-reinforced backs address cracking and breaking under foot pressure, and the listed resistance to fading, corrosion, and UV damage is relevant for bars exposed to weather. Four pads provide a coordinated replacement set, each measuring 21 by 3 inches. A rubber mallet and 24 pins support the installation workflow. Compatibility is limited to 3-inch round bars with a five-pin mounting configuration; matching the existing dimensions and holes is essential before fitting.

Pros
  • Four 21-by-3-inch pads in the set
  • Grid-reinforced polymer backs
  • Listed resistance to fading, corrosion, and UV damage
  • Includes 24 pins and rubber mallet
Cons
  • Fits only 3-inch round bars with the specified five-pin configuration.

Skip it if you have oval, flat, or differently sized bars; RXL RuggedXL STP1126 also specifies 3-inch round bars, not those shapes.

Choose this set when replacing four pads on matching 3-inch round, five-pin bars and you want the mallet and clips together. Its narrowly specified mounting pattern makes measuring the existing setup important before installation.

Full product details
BrandIexcauw
ColorBlack
Compatible with Vehicle TypeThis pad is NOT universal. It is specifically designed for 3-inch round bars with a 5-PIN mounting configuration. Total Length: 21 inches. Width: 3 inches. Please verify your existing hardware matches these dimensions exactly., To avoid return hassles, measure the distance between your mounting hole
Included Components24 pins, 4Pack replacement pads, Rubber mallet
Item Dimensions21 x 3 x 3 inches
Dimensions21 x 3 x 3 inches
ManufacturerIexcauw
Part NumberNBS4P001
Manufacturer Warranty Description2 Year
MaterialPlastic
Model NumberNBS4P

Listed on Amazon as: Replacement Step Pad for 3" Round Nerf Bars Set of 4 Pack, 21" Long x 3" Wide, Durable Non-Slip Running Boards Replacement Pads with Rubber Mallet and 24 Pins

View on Amazon
Generic 21-Inch Pad Kit

#2 · Best Tool Bundle

2. Generic 21-Inch Pad Kit

  • dimensions: 21 x 3 x 3 in
  • Weight: 2.4 lb
  • Material: Acrylonitrile Butadiene Styrene (ABS)
  • Compatible with Vehicle Type: 3-5/8", 6-3/8", 5-5/8", 3-5/8" from one end…

Best for: Drill-bit-equipped four-pack.

Why it ranks #2: The four-pad kit includes 25 pins, a rubber hammer, and a drill bit; its listed five-hole spacing helps buyers verify a close match.

A special drill bit joins the rubber hammer and 25 installation pins in this four-pad kit, giving the replacement job more supplied hardware and tools. The ABS pads measure 21 by 3 inches and are specified for 3-inch round nerf bars with a five-hole arrangement.

Four 21-by-3-inch ABS pads provide a full replacement set, while the included rubber hammer supports tapping the pads into place. The package also lists a special drill bit and 25 tubular nuts, giving the installer tools and mounting components together. Fit depends on the tube diameter and pin spacing rather than vehicle model, with the supplied dimensions specifying a 3-inch round tube and five-hole pattern. Measure the old setup before installation to check alignment.

Pros
  • Four 21-by-3-inch ABS pads
  • Includes 25 tubular nuts
  • Rubber hammer and special drill bit included
  • Fit specified by tube size and hole spacing
Cons
  • The fit is restricted to 3-inch round bars with the stated five-hole spacing.

Skip it if you need pads for a four-hole or differently sized bar; JUFZQO's WSPKITTKE0712 also specifies a five-hole, 3-inch round fit.

Consider this kit for a four-pad replacement on matching 3-inch round bars when the included hammer, drill bit, and tubular nuts suit your installation. Confirm the existing hole spacing; vehicle model alone does not establish fit.

Full product details
BrandGeneric
ColorBlack
Compatible with Vehicle Type3-5/8", 6-3/8", 5-5/8", 3-5/8" from one end pin to the other, Nerf Bar Replacement Pads for 3" Round Tubes with 5 Holes
Included Components25 Tubular Nuts, 3" Round Ne,rf Bars Set of 4 Pack, 21 x 3 x 3 inches, Drill bit, Manual, Rubber hammer
Item Dimensions21 x 3 x 3 inches
Item Weight2.4 pounds
Dimensions21 x 3 x 3 inches
ManufacturerFat Girlstore
Part NumberNe,rf Bar Replacement Pads
Manufacturer Warranty Description1 Year
MaterialAcrylonitrile Butadiene Styrene (ABS)
Model Number3" Round Nerf Bars

Listed on Amazon as: Nerf Bar Replacement Pads Kit for 21" x 3" Round Nerf Bars Set of 4 Pack

View on Amazon
XNGQUEY 0001

#3 · Best Spacing Detail

3. XNGQUEY 0001

  • dimensions: 21 x 3 x 2 in
  • Weight: 1.4 lb
  • Material: Plastic
  • Compatible with Vehicle Type: 3" Round Step Pads, Truck, nerf bar…

Best for: Measured-fit four-pad set.

Why it ranks #3: This four-pack specifies 21-by-3-inch pads and pin intervals of 3-5/8, 5-5/8, 6-3/8, and 3-5/8 inches, plus 24 clips.

The stated 19.48-inch outer-hole spacing gives this XNGQUEY four-pad set a concrete measurement to check against existing steps. Each pad measures 21 by 3 inches and is intended for 3-inch round tubes with a five-hole layout, with 24 clips included for installation.

The listed pin-to-pin sequence—3-5/8, 5-5/8, 6-3/8, and 3-5/8 inches—helps buyers compare the mounting pattern with an old pad before removing all four. That measurement-led approach matters because the product specifies fit by tube diameter and hole spacing, not vehicle model. Four pads and 24 clips support a complete replacement, while the plastic construction provides the listed pad material. Confirm both the 3-inch tube and hole pattern before fitting.

Pros
  • Four replacement pads included
  • Twenty-four clips supplied
  • Lists 19.48-inch outer-hole spacing
  • Specifies a 3-inch round, five-hole fit
Cons
  • A matching 3-inch tube alone is insufficient; the hole spacing must also match.

Skip it if you cannot verify the five-hole spacing; MEFDUK ADD-RSP-260522 lists the same pin-to-pin measurements for its four-pad set.

A sensible option for replacing four pads when you can compare the listed outer-hole and pin-to-pin measurements with your existing bars. It is limited to the specified 3-inch round, five-hole layout, not a vehicle-model-based fit.

Full product details
BrandXNGQUEY
ColorBlack
Compatible with Vehicle Type3" Round Step Pads, Truck, nerf bar replacement pads
Included Components24*Clips, 4*Step Pads
Item Dimensions21 x 3 x 2 inches
Item Weight1.4 pounds
Dimensions21 x 3 x 2 inches
ManufacturerXINGJIAN01
Part Number0001
Manufacturer Warranty Description2 Year Manufacturer
MaterialPlastic
Model Number0001

Listed on Amazon as: Nerf Bar Replacement Pads for 3" Round Tubes with 5 Holes, 21" X 3"(19.48" Outer Hole Spacing) – Durable Non-Slip Replacement Step Pad Set of 4, Easy Installation——Verify Tube Size & Hole Spacing!

View on Amazon
RuggedXL STP1126

#4 · Best Clip Supply

4. RuggedXL STP1126

  • dimensions: 21 x 3 x 2 in
  • Material: Plastic
  • Compatible with Vehicle Type: 3" Round Step Pads, This product is a…

Best for: Four-pad five-pin replacement.

Why it ranks #4: Four 21-by-3-inch pads come with 20 installation clips, identified as five per pad; the listing clearly excludes 4- or 5-inch and oval bars.

Twenty included clips—five for each pad—are the practical differentiator in this four-piece RuggedXL kit. The 21-by-3-inch black plastic pads have an uneven texture for a firm stepping grip, and the set is specifically limited to 3-inch round nerf bars rather than oval or flat steps.

The uneven pad texture is described as providing firm grip when stepping, while the 21-by-3-inch dimensions help identify whether the replacement matches the existing step surface. Four pads and 20 clips are included, with five mounting pins per pad for installation. The product expressly excludes 4- and 5-inch round bars and flat-style nerf bars. Removing an old pad to check its dimensions and pin locations helps establish whether this specific replacement kit aligns.

Pros
  • Four black plastic replacement pads
  • Uneven texture provides a firm grip
  • Twenty clips supply five per pad
  • Specifies 21-by-3-inch pad dimensions
Cons
  • Does not fit 4- or 5-inch round bars or flat-style nerf bars.

Skip it if you have oval or flat running boards; Westin 25-0001 is another narrow-fit option, but only for Westin Signature 3 bars.

This kit suits owners replacing all four pads on 3-inch round bars who want five included clips per step and a textured surface. It is not a solution for larger round tubes or flat-style nerf bars.

Full product details
BrandRXL RuggedXL
ColorBlack
Compatible with Vehicle Type3" Round Step Pads, This product is a non-specific fitment, universal, Truck, WSP001KIT
Included Components(20) Clips, (4) Step Pads
Item Dimensions21 x 3 x 2 inches
Dimensions21 x 3 x 2 inches
ManufacturerRXL RuggedXL
Part NumberSTP1126
Manufacturer Warranty Description1 Year Manufacturer
MaterialPlastic
Model NumberSTP1126
Additional InformationImportant Information Small parts. Not for children under 3 yrs.

Listed on Amazon as: RuggedXL WSP001KIT Replacement Step Pad for 3" Round Nerf Bars – Set of 4

View on Amazon
MEFDUK 5-Hole Pads

#5

5. MEFDUK 5-Hole Pads

  • dimensions: 4.31 x 5.12 x 22.44 in
  • Weight: 1.5 kg
  • Material: Metal, Plastic
  • Compatible with Vehicle Type: fit for 3" Round Step Pads

Best for: Weather-resistant four-pad set.

Why it ranks #5: Its four-pad set lists 3-inch round tubes, a 21-by-3-inch size, matching pin intervals, and 20 mounting pins.

Reinforced PVC plastic paired with a metal structure is this MEFDUK set’s defining construction feature, with listed weather and corrosion resistance for outdoor steps. Four 21-by-3-inch pads and 20 mounting pins are supplied for 3-inch round tubes using the stated five-hole pattern.

The reinforced PVC and metal structure are described as resisting cracking, aging, weather, and corrosion, supporting use on exposed side steps. The 21-by-3-inch pad size and stated pin-to-pin sequence—3-5/8, 5-5/8, 6-3/8, and 3-5/8 inches—help buyers check alignment with existing mounts. Four pads and 20 pins support a full set replacement. This is specified for 3-inch round bars with five holes, so compare the pattern before installation.

Pros
  • Reinforced PVC plastic with metal structure
  • Listed resistance to weather, corrosion, and cracking
  • Four 21-by-3-inch pads included
  • Twenty mounting pins supplied
Cons
  • The listing provides no manufacturer warranty.

Skip it if you want a listed warranty; Iexcauw NBS4P specifies a reinforced four-pad set with a manufacturer warranty description.

Choose this set when replacing four pads on a measured 3-inch round, five-hole bar and outdoor exposure makes the listed weather resistance relevant. Check the pin sequence against your existing mounts before committing to the fit.

Full product details
BrandMEFDUK
Compatible with Vehicle Typefit for 3" Round Step Pads
Included Components4 step pads and 20 mounting pins
Item Dimensions4.31 x 5.12 x 22.44 inches
Item Weight1.5 kg
Dimensions4.31 x 5.12 x 22.44 inches
ManufacturerHKjiqiao
Part NumberWSP001KIT
Manufacturer Warranty DescriptionNo
MaterialMetal, Plastic
Model NumberADD-RSP-260522

Listed on Amazon as: Nerf Bar Replacement Pads Fit for 3" Round Tubes with 5 Holes

View on Amazon
JUFZQO Upgraded Pads

#6

6. JUFZQO Upgraded Pads

  • dimensions: 21 x 3 x 2 in
  • Weight: 0.7 kg
  • Material: Plastic
  • Compatible with Vehicle Type: 3" Round Step Pads

Best for: Temperature-resistant polymer pads.

Why it ranks #6: These polymer pads specify 3-inch round tubes and the five-hole spacing pattern, while expressly excluding four-hole designs and other tube sizes.

High-performance polymer with listed resistance to extreme temperatures, cracking, fading, and corrosion distinguishes this JUFZQO replacement set. The pads measure 21 by 3 inches and target 3-inch round side tubes with five holes, using the specified pin-spacing sequence for alignment.

The polymer’s stated resistance to cracking, fading, corrosion, and extreme temperatures is relevant for steps exposed to changing outdoor conditions. The 21-by-3-inch size gives a concrete surface dimension to compare with existing pads, while the listed hole spacing—3-5/8, 5-5/8, 6-3/8, and 3-5/8 inches—helps check mounting alignment. Compatibility is expressly limited to five-hole, 3-inch round tubes; the listing excludes four-hole designs and other tube sizes, so verify the setup first.

Pros
  • High-performance polymer construction
  • Listed resistance to extreme temperatures and fading
  • 21-by-3-inch pad dimensions
  • Specific five-hole spacing is provided
Cons
  • Not compatible with four-hole designs or other tube sizes.

Skip it if you have a four-hole pattern; RXL RuggedXL STP1126 also requires five mounting pins per pad on 3-inch round bars.

This replacement is suited to buyers with five-hole, 3-inch round tubes who value the listed weather and temperature resistance. Its precise pattern excludes four-hole layouts and other tube diameters, so compare the measurements first.

Full product details
BrandJUFZQO
Colorblack
Compatible with Vehicle Type3" Round Step Pads
Item Dimensions21 x 3 x 2 inches
Item Weight0.7 kg
Dimensions21 x 3 x 2 inches
ManufacturerTakemyParts
Part NumberWSPKITTKE0712
MaterialPlastic
Model NumberNerf Bar Replacement Pads

Listed on Amazon as: Upgraded Nerf Bar Replacement Pads Fit for 3" Round Tubes with 5 Holes

View on Amazon
Iexcauw NBS2P

#7 · Best Two-Pack

7. Iexcauw NBS2P

  • dimensions: 21 x 3 x 3 in
  • Weight: 0.7 kg
  • Material: Plastic
  • Compatible with Vehicle Type: Verify tube diameter (3") & hole spacing…

Best for: Reinforced two-pad replacement.

Why it ranks #7: The two 21-by-3-inch pads suit a partial replacement, with 12 pins and a rubber mallet; confirm the listed 3-inch, five-hole fit.

A reinforcement grid beneath each 21-by-3-inch polymer pad is the defining feature, helping it withstand repeated foot pressure while replacing worn steps. This two-pad set targets 3-inch round nerf bars with a five-hole mounting pattern, and includes pins and a rubber mallet for installation.

The reinforced underside is intended to resist cracking under repeated stepping, while the listed resistance to fading, corrosion, and UV damage suits exposed off-road or coastal use. Each pad measures 21 by 3 inches, so the replacement keeps the listed running-board footprint. Twelve pins and a rubber mallet are included, giving you installation hardware and a tapping tool in the package. Fit depends on both the 3-inch tube and the stated five-hole spacing, so measure before starting.

Pros
  • Reinforcement grid beneath the polymer pads
  • Listed resistance to fading, corrosion, and UV damage
  • Two 21-by-3-inch pads included
  • Includes 12 pins and a rubber mallet
Cons
  • Only two pads are included, fewer than a four-pad set.

Skip it if you need to replace four step pads at once; Iexcauw's four-pad NBS4P set includes 24 pins and a mallet.

A practical match for owners replacing two worn pads on 3-inch round, five-hole bars, especially where sun or coastal exposure matters. Check the tube diameter and hole spacing carefully; this set covers only two pads.

Full product details
BrandIexcauw
ColorBlack
Compatible with Vehicle TypeVerify tube diameter (3") & hole spacing (3-5/8", 5-5/8", 6-3/8", 3-5/8") before purchase. These running boards replacement pads are designed to fit 3-inch round Running Boards with a 5-hole setup, replacing worn originals without any wobble.
Included Components12 pins, 2 Pack replacement pads, Rubber mallet
Item Dimensions21 x 3 x 3 inches
Item Weight0.7 kg
Dimensions21 x 3 x 3 inches
ManufacturerIexcauw
Part NumberNBS2P001
Manufacturer Warranty Description2 Year
MaterialPlastic
Model NumberNBS2P

Listed on Amazon as: Set of 2 Nerf Bar Replacement Step Pads for 3" Round Tubes with 5 Holes Only – 21" x 3" Non-Slip Upgraded Durable Running Board Pads, Easy Installation with Included Rubber (Verify Tube Size)

View on Amazon
USHDHDID 25-0001

#8

8. USHDHDID 25-0001

  • dimensions: 20 x 4 x 2.7 in
  • Material: Plastic
  • Compatible with Vehicle Type: Van

Best for: Westin Signature 3 two-pack.

Why it ranks #8: This two-pack is listed for Signature 3 bars and 3-inch round nerf bars, with 10 barrel clips; its stated pad length is 19.5 inches.

Compatibility with Westin Signature 3 nerf step bars distinguishes this two-pad kit from generic round-bar replacements. The black polymer pads are described as non-slip, measure 19.6 by 3 inches in the title, and come with 10 barrel clips for mounting on the specified 3-inch round bars.

The Signature 3 fit designation gives owners of those step bars a specific replacement target, while the stated 19.6-by-3-inch pad size helps compare the step surface with the worn original. Black polymer construction and the non-slip description identify the material and stepping surface. Ten barrel clips are included with the two-pad kit, providing mounting pieces for installation. The product is listed for 3-inch round nerf bars, so verify the bar series and pad dimensions before ordering.

Pros
  • Specified for Westin Signature 3 nerf step bars
  • Two black polymer pads included
  • Non-slip surface described in the title
  • Includes 10 barrel clips
Cons
  • The set includes two pads, not enough to replace four steps.

Skip it if you need one Westin Signature 3 pad and four clips; Westin 25-0001 is the single-pad kit for that bar series.

This kit fits buyers refreshing two pads on Signature 3 bars who want barrel clips supplied with the polymer replacements. Its two-pad quantity and series-specific fit make it a poor match for other bar styles or a four-pad job.

Full product details
BrandUSHDHDID
ColorBlack
Compatible with Vehicle TypeVan
Included ComponentsStep Pad Kit
Item Dimensions20 x 4 x 2.7 inches
Dimensions20 x 4 x 2.7 inches
ManufacturerUSHDHDID
Part Number25-0001
Manufacturer Warranty Description2 Year
MaterialPlastic
Model Number25-0001

Listed on Amazon as: 25-0001 Replacement Step Pad Kit Fits for Signature 3 Nerf Step Bars, 19.6" x 3" Black Polymer Non-Slip Running Board Step Pad for 3-Inch Round Nerf Bars, Includes 10 Barrel Clips (2 Pack)

View on Amazon
Westin 25-0001

#9

9. Westin 25-0001

  • Weight: 11.2 oz

Best for: Signature 3 single-pad replacement.

Why it ranks #9: This is a direct series-specific option for Westin Signature 3 bars, but it includes only one 20-inch pad and four clips and excludes other bars.

A precise fit for Westin Signature 3 Nerf Step Bars is the central advantage of this one-pad kit. The 20-inch replacement includes four installation clips, giving owners of that specific bar series the pad and clips in one package for a targeted repair.

The 20-by-3-inch pad dimensions identify the replacement surface, while the Signature 3-only compatibility prevents treating it as a generic 3-inch round-bar pad. Four clips are included to secure the single replacement pad during installation. Westin states that it will not fit other Westin or non-Westin 3-inch round nerf step bars, so matching the bar series is essential. The single-pad quantity suits an individual damaged step, rather than a full multi-pad refresh.

Pros
  • One 20-inch replacement pad included
  • Specified only for Westin Signature 3 bars
  • Four installation clips included
  • Dimensions listed as 20 by 3 inches
Cons
  • Only one pad is included, and the clips are required for installation.

Skip it if you need a two-pad kit; USHDHDID 25-0001 lists two pads and 10 barrel clips for Signature 3 bars.

A focused repair choice for a Westin Signature 3 owner replacing one 20-inch pad. The series-specific fit and single-pad quantity are important boundaries; it does not suit other round-bar brands or a multi-step replacement.

Full product details
BrandWestin
Item Weight‎11.2 ounces
Item model number‎25-0001
Manufacturer‎Westin
Part Number‎25-0001
Model‎25-0001
Dimensions‎20 x 3 x 0.5 inches
Special Features‎Fits Westin Signature 3 Series Nerf Step Bars ONLY, Includes one replacement step pad and 4 installation clips
Additional InformationImportant information

Listed on Amazon as: Westin 25-0001 Replacement Step Pad Kit

View on Amazon
Dee Zee DZ4INCHECKS

#10

10. Dee Zee DZ4INCHECKS

  • dimensions: 28 x 6 x 6 in
  • Weight: 2 lb
  • Material: Aluminum
  • Compatible with Vehicle Type: Truck

Best for: Dee Zee four-bar step set.

Why it ranks #10: The listing identifies pads for four nerf bars but warns styles are not interchangeable, and its aluminum construction gives less specific fit detail here.

The DZ4INCHECKS listing specifies step pads for four nerf bars and includes clips to secure them, making it a multi-step option for a compatible Dee Zee setup. Its aluminum construction distinguishes it from the plastic replacement pads in this roundup.

The four-bar description and included securing clips point to a set intended to cover multiple steps, while aluminum construction identifies its listed material. Dee Zee explicitly cautions that step-pad styles are not interchangeable, making style matching central to the buying decision. The listing does not provide a specific tube diameter or hole-spacing pattern, so use the pad-style designation and existing step configuration to establish compatibility before installation rather than assuming a universal fit.

Pros
  • Described for four nerf bars
  • Clips included to secure pads to the step
  • Aluminum construction
  • Dee Zee model DZ4INCHECKS identified
Cons
  • Step-pad styles are not interchangeable, and no tube diameter or hole spacing is listed.

Skip it if you need a specified 3-inch round, five-hole fit; MEFDUK ADD-RSP-260522 lists that pattern and its pin spacing.

This option may suit a Dee Zee owner seeking pads for four bars with securing clips included. Because styles are not interchangeable and no hole pattern is specified, match the existing Dee Zee step-pad style before installation.

Full product details
BrandDEE ZEE
ColorBlack
Compatible with Vehicle TypeTruck
Included ComponentsPer Item Description
Item Dimensions28 x 6 x 6 inches
Item Weight2 pounds
Dimensions28 x 6 x 6 inches
ManufacturerDee Zee
Part NumberDZ4INCHECKS
Manufacturer Warranty Description30 Days
MaterialAluminum
Model Number300-DZ4INCHECKS
Additional InformationImportant Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Listed on Amazon as: Dee Zee DZ4INCHECKS Step Pads for Nerf Bars

View on Amazon

Why matching the pin pattern matters

A replacement pad can be the right length and still fail to mount if its pin pattern does not match the bar. Several kits here specify a five-hole layout with pin intervals of 3-5/8, 5-5/8, 6-3/8, and 3-5/8 inches, while RuggedXL identifies five pins per pad. JUFZQO explicitly excludes four-hole designs.

Treat those details as a fit check, not a promise that every 3-inch round bar accepts the pad. Before removing the old part, record the tube diameter, pad length and width, number of holes, and distance between pin locations.

Compare those measurements with the product listing; do not rely only on a vehicle model or the phrase “universal.” If a new pad will not align, stop rather than forcing its clips into place, since the supplied listings do not establish that mismatched holes can be safely adapted.

When a brand-specific pad is the safer match

A brand-specific replacement is the more appropriate route when your existing bar is identified as a particular series and the listing limits fit to that series. Westin 25-0001 states it fits only Westin Signature 3 Nerf Step Bars, and says its single pad includes four clips. The USHDHDID 25-0001 listing also names Signature 3 bars, but describes a two-pack with 10 barrel clips and a 19.5-inch pad.

Those packages and stated lengths differ, so compare the old pad and hardware before treating the similar model number as interchangeable. For other 3-inch round bars, the multi-pad products provide broader stated fit patterns, but they still require measurement.

Dee Zee’s listing warns that step-pad styles are not interchangeable, making its style-specific caution relevant even though the supplied details do not give a matching hole pattern.

How to Choose Nerf Bar Step Pads

Tube diameter and hole pattern

Look for a product that matches both your bar’s tube diameter and its mounting holes. Many options here specify 3-inch round tubes and five-hole layouts; several list intervals of 3-5/8, 5-5/8, 6-3/8, and 3-5/8 inches. JUFZQO says it will not fit four-hole designs or other tube sizes, and RuggedXL rules out 4- and 5-inch round, oval, and flat bars.

Westin’s pad is narrower still: it fits Signature 3 bars only. Buyers with a confirmed five-hole, 3-inch setup can compare the broader kits; owners of a named Westin series should check the specific Westin replacement.

Measure first if the existing bar’s pattern is uncertain.

Pad size and replacement quantity

Choose a pad length and pack size that match the parts you need to replace. Several general-fit kits list four pads measuring 21 by 3 inches, while Iexcauw’s NBS2P provides two pads at the same stated size. The Westin 25-0001 is a single 20-inch pad; the USHDHDID listing gives a 19.5-inch pad in a two-pack.

These differences matter when replacing one worn step, several pads, or a complete set. Buyers replacing multiple matching 21-inch pads can consider the four-packs, while a partial repair may call for a smaller pack.

For a brand-specific pad, compare the old pad’s actual length as well as its series and mounting layout.

Included mounting hardware and tools

Check whether the package includes enough clips and whether it supplies tools for installation. Included hardware ranges from the Westin single pad’s four clips to kits with 20 or 24 clips; RuggedXL lists five clips per pad. The Generic kit adds 25 pins, a rubber hammer, and a special drill bit, while both Iexcauw packs include a rubber mallet and pins.

The Westin product description says its required barrel clips are sold separately, though the feature listing also describes four included clips, so verify the package details before ordering. A buyer who already has tools may prefer to focus on matching pads and clips; someone replacing a full set may find a larger clip supply more convenient.

Which Nerf Bar Step Pads Should You Choose?

For a confirmed 3-inch round bar with the listed five-pin pattern, choose Iexcauw NBS4P for four 21-by-3-inch pads, 24 pins, and a mallet. If you want a kit that adds a rubber hammer and drill bit, consider Generic 21-Inch Pad Kit after checking its hole spacing. For a partial replacement, Iexcauw NBS2P supplies two matching-size pads and 12 pins.

Choose Westin 25-0001 only when your bars are Westin Signature 3 and you need its specific single-pad replacement; USHDHDID 25-0001 is another listed Signature 3 option with two pads. Do not choose by vehicle model alone.

Measure tube diameter, pad dimensions, and pin positions before ordering, and avoid Dee Zee DZ4INCHECKS unless its particular pad style matches your bars.

Frequently Asked Questions

How do I measure nerf bar tube diameter and pin spacing before ordering?

Measure the tube across its outside diameter, then compare that measurement with the listing. Remove an existing pad if possible and measure its length, width, and the distance between pin holes, using the same reference points as the product description. Match the hole count and layout too; a similar tube diameter alone does not confirm fit.

Can replacement step pads fit a different brand of nerf bar?

They may fit, but brand names alone cannot confirm compatibility. Compare the replacement’s tube diameter, pad dimensions, hole count, and pin positions with your existing bar or pad. Some listings specify a particular bar, such as Westin Signature 3, while others warn that their pads are not universal.

Order only when the measurements and mounting layout match.

What should I do if a new pad does not line up with the mounting holes?

Stop before forcing the pins or pad into place. Recheck the pad’s orientation, hole spacing, tube size, and the old pad’s measurements against the listing. If they still do not align, the pad may not match your bar; contact the seller about fit or seek a compatible replacement rather than altering the mounting holes.

Should I replace one pad or a full set?

Choose the quantity that matches the pads you need to replace and the listing’s contents. The options here include a single pad, two-pad sets, and four-pad kits; some listings also specify included pins or installation tools. Confirm the pad dimensions and mounting pattern before deciding, since a larger set does not resolve a fit mismatch.

Which measurements should I compare besides tube diameter?

Compare the replacement pad’s length and width, the number of mounting holes, and the spacing between those holes. For example, several listings specify 21-by-3-inch pads and five-hole layouts, while another gives outer hole spacing. Use your existing pad or bar as the reference, and do not rely on vehicle model alone.

Final Words

Start by measuring tube diameter, pad dimensions, and pin layout; do not choose by vehicle model alone. For a confirmed 3-inch round bar with the stated five-pin pattern, the Iexcauw four-pack is the article’s Best Overall pick. Consider the Generic kit if its hole spacing matches and you want its listed tools, or the two-pad Iexcauw set for a partial replacement.

Choose Westin-specific options only for Signature 3 bars, and verify Dee Zee pad style before ordering.

Leave a Reply

Your email address will not be published. Required fields are marked *