Best Tow Ramps For Low Cars: Compare 10 Loading Options

Best Tow Ramps For Low Cars

A strong tow ramp for a low car creates a gradual transition, fits the trailer or carrier setup, and has enough capacity for the vehicle and loading conditions. Race Ramps Tow Ramps 74-inch HD leads this selection for flatbed operators: its solid-core, 74-inch design is made for low-clearance cars and weighs 15 pounds per ramp. The options here range from long trailer-loading ramps with approach angles as low as 4.3 degrees to compact starter ramps and garage-maintenance ramps with steeper inclines.

That distinction matters: the best match depends on whether you need to bridge a trailer edge, extend an existing ramp, or raise a car for service. Compare the listed dimensions, capacity, and material, then check fit and safe use with your vehicle and equipment before loading.

Race Ramps Tow Ramps 74-inch HD is the leading choice for low-car towing because it is specifically described for flatbed tow trucks and low-clearance cars. Each ramp has a solid core, weighs 15 pounds, and has a listed 1,500-pound capacity. For a gentler trailer approach, Race Ramps Foam Trailer Loading Ramps offer a 4.3-degree angle and a built-in trailer-door notch.

Choose between these designs based on your loading setup, clearance needs, and the capacity required for each ramp.

Our Top Picks

Race Ramps Tow Ramps 74-inch HDBest Overall

Race Ramps Tow Ramps 74-inch HD

Designed for flatbed tow trucks and low-clearance cars, this solid-core ramp is 74 inches long, weighs 15 pounds, and lists 1,500-pound capacity.

View on Amazon
Race Ramps Foam Trailer Loading RampsGentlest Approach

Race Ramps Foam Trailer Loading Ramps

Its 4.3-degree approach and built-in 5-by-2-inch trailer-door notch support a gradual transition when loading low-clearance cars onto trailers.

View on Amazon
MaxRamps Car Hauler Ramp 7-inchLong One-Piece

MaxRamps Car Hauler Ramp 7-inch

The 74-inch, one-piece ramp has a 5.5-degree angle and supports 1,750 pounds per ramp, fitting hauler use with tires up to 12 inches wide.

View on Amazon

Compare these low-car ramp options

#ProductDimensionsLoad CapacityMaterialBuy
110"L x 10"W x 10"H1500 lb—View on Amazon
210"L x 10"W x 10"H1500 lbExpanded foam with traction coatingView on Amazon
374"L x 14"W x 7"H3500 lbFoam, Polyurethane (PU)View on Amazon
431.5"L x 19.69"W x 3.54"H4409lbs/PC lbPolypropylene (PP)View on Amazon
5
ROBLOK 6-degree Trailer Ramps5. ROBLOK 6-degree Trailer RampsSl absolutely low trailer transitions
31.5"L x 19.7"W x 3.5"H4409lbs/PC lbPolypropylene (PP)View on Amazon
6
Vraxelor 4-inch Trailer Ramps6. Vraxelor 4-inch Trailer RampsCompact EVA trailer ramps
36"L x 12"W x 4"H3000 lbEva FoamView on Amazon
7
Chantmo 4-inch Trailer Ramps7. Chantmo 4-inch Trailer RampsLong low-profile trailer ramps
46"L x 14"W x 4"H3000 lb—View on Amazon
8
Mytee Products Starter Tow Ramp8. Mytee Products Starter Tow RampSteel-bed transition bridges
10"L x 10"W x 10"H—NylonView on Amazon
9
ROBLOK Low-Profile Garage Ramps9. ROBLOK Low-Profile Garage RampsGarage jack-access ramps
17.5"L x 10"W x 3.14"H5 tonPlasticView on Amazon
10
Pyle Heavy Duty Vehicle Ramps10. Pyle Heavy Duty Vehicle RampsHigh-clearance maintenance users
36"L x 13"W x 8.5"H13000 lbPlasticView on Amazon

Detailed Reviews: Best Tow Ramps For Low Cars

Race Ramps Tow Ramps 74-inch HD

#1 · Best Overall

1. Race Ramps Tow Ramps 74-inch HD

  • Dimensions: 10"L x 10"W x 10"H
  • Load Capacity: 1500 lb

Best for: Flatbed rollback operators.

Why it ranks #1: Designed for flatbed tow trucks and low-clearance cars, this solid-core ramp is 74 inches long, weighs 15 pounds, and lists 1,500-pound capacity.

A 74-inch single-piece profile gives this RACE RAMPS tow ramp a long transition for loading low-clearance cars onto flatbed tow trucks. Its solid core, non-slip coating, and reinforced bottom focus the setup on repeat hauling, while the 15-pound weight per ramp keeps each piece manageable to position.

The 74-inch length is intended to ease the transition for low cars, and the solid-core construction supplies a single-piece ramp rather than a multi-section setup. A durable non-slip coating provides traction at the surface, while the reinforced bottom addresses wear where the ramp meets the ground. Each ramp weighs 15 pounds and has a listed 1,500-pound capacity, so operators can handle the pieces individually while keeping the per-ramp load limit in view during flatbed work.

Pros
  • 74-inch single-piece ramp for flatbed tow trucks
  • Solid-core construction
  • Non-slip coating
  • Reinforced bottom; 15 pounds per ramp
Cons
  • The listed capacity is 1,500 pounds per ramp, limiting its stated load rating.

Skip it if you need a stated capacity above 1,500 pounds per ramp; MaxRamps MRTX-7 lists 1,750 pounds per ramp.

For tow operators loading low-clearance cars onto flatbeds, this ramp combines a long 74-inch run with a grippy surface. Its stated 1,500-pound per-ramp capacity is the key boundary to check against the hauling load.

Full product details
BrandRACE RAMPS
ColorBlack
Dimensions10"L x 10"W x 10"H
Item Weight15 pounds
Load Capacity1500 pound
ManufacturerRace Ramps
Part NumberBT-TT-7-10
Model NumberBT-TT-7-10
Additional InformationImportant Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Listed on Amazon as: Tow Ramps – 74" Flatbed HD Ramps BT-TT-7-10

View on Amazon
Race Ramps Foam Trailer Loading Ramps

#2 · Gentlest Approach

2. Race Ramps Foam Trailer Loading Ramps

  • Dimensions: 10"L x 10"W x 10"H
  • Load Capacity: 1500 lb
  • Material: Expanded foam with traction coating

Best for: Foam trailer ramp loading.

Why it ranks #2: Its 4.3-degree approach and built-in 5-by-2-inch trailer-door notch support a gradual transition when loading low-clearance cars onto trailers.

A built-in five-by-two-inch trailer-door notch connects these RACE RAMPS directly to the trailer edge, creating a smoother transition for low-profile cars. The five-inch height and 4.3-degree approach help reduce scraping risk, while traction-coated expanded foam keeps the pair relatively light to handle.

The 4.3-degree approach is intended to reduce contact with bumpers, splitters, and undercarriages as low cars load. Its five-by-two-inch notch meets the trailer door, eliminating the gap and supporting a more controlled transition. Each expanded-foam ramp has a traction coating and a 1,500-pound rating, for 6,000 pounds across the pair as supplied. At five inches high, this setup gives more rise than a small starter ramp while remaining a foam trailer-loading option.

Pros
  • 4.3-degree approach angle
  • Built-in 5 × 2-inch trailer-door notch
  • Traction-coated expanded foam
  • 1,500 pounds per ramp; 6,000 pounds per pair
Cons
  • The listed 1,500-pound capacity per ramp is lower than MaxRamps MRTX-7's 1,750 pounds.

Skip it if you need more than 1,500 pounds of capacity per ramp; MaxRamps MRTX-7 lists 1,750 pounds per ramp.

Low-car owners loading onto a trailer can use this pair for its gentle approach and notched door connection. Keep the stated 1,500-pound per-ramp rating and five-inch height in view when checking the job.

Full product details
BrandRACE RAMPS
ColorBlack
Dimensions10"L x 10"W x 10"H
Item Weight5.65 kg
Load Capacity1500 pound
ManufacturerBrute Industries, Inc.
Part NumberRR-TR-5
Manufacturer Warranty Description1 year limited warranty against manufacturer defects.
MaterialExpanded foam with traction coating
Model NumberRR-TR-5
Additional InformationImportant Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov

Listed on Amazon as: Race Ramps Foam Trailer Loading Ramps for Low-Profile Cars, 5 In H, Pair

View on Amazon
MaxRamps Car Hauler Ramp 7-inch

#3 · Long One-Piece

3. MaxRamps Car Hauler Ramp 7-inch

  • Dimensions: 74"L x 14"W x 7"H
  • Load Capacity: 3500 lb
  • Material: Foam, Polyurethane (PU)

Best for: Long solid-core hauler ramps.

Why it ranks #3: The 74-inch, one-piece ramp has a 5.5-degree angle and supports 1,750 pounds per ramp, fitting hauler use with tires up to 12 inches wide.

A 74-inch one-piece length and five-and-a-half-degree approach give the MaxRamps MRTX-7 a long transition for loading classic, show, race, and exotic cars. Its seven-inch lift adds height, while the solid-core EPS construction and polyurea coating provide a durable, lightweight ramp surface.

The 74-by-14-inch one-piece format gives tires a long loading run, and the five-and-a-half-degree angle is intended for low-angle loading and unloading. A seven-inch lift adds substantial height at the hauler edge; the stated fit accommodates tires up to 12 inches wide. Solid-core high-density EPS with a polyurea coating combines the stated strength and durability with a 14-pound per-ramp weight. Capacity is listed as 1,750 pounds per ramp, 3,500 pounds per set.

Pros
  • 74-inch one-piece ramp
  • Five-and-a-half-degree approach and seven-inch lift
  • Accommodates tires up to 12 inches wide
  • 1,750 pounds per ramp; 3,500 per set
Cons
  • At 14 pounds per ramp, it weighs more than the 15-pound-per-ramp RACE RAMPS flatbed model.

Skip it if you need a 4.3-degree approach and trailer-door notch; RACE RAMPS RR-TR-5 provides both for trailer loading.

For haulers of classic or low-clearance cars needing a long run and seven inches of lift, this one-piece ramp offers a substantial transition. Check the 12-inch tire-width accommodation and per-ramp capacity against the vehicle.

Full product details
BrandMaxRamps
ColorBlack
Dimensions74"L x 14"W x 7"H
Item Weight28 pounds
Load Capacity3500 Pounds
ManufacturerMaxRamps
MaterialFoam, Polyurethane (PU)
Model NumberMRTX-7

Listed on Amazon as: Car Hauler Low-Profile Ramp 7"

View on Amazon
HOXWELL 3.5-inch Trailer Ramps

#4 · Wide Starter Ramps

4. HOXWELL 3.5-inch Trailer Ramps

  • Dimensions: 31.5"L x 19.69"W x 3.54"H
  • Load Capacity: 4409lbs/PC lb
  • Material: Polypropylene (PP)

Best for: Low-angle trailer loading.

Why it ranks #4: The 31.5-inch ramps have a 6-degree incline, anti-slip features, and a listed 4,409-pound-per-piece capacity for extending trailer access.

A six-degree approach angle gives these HOXWELL ramps a gradual route for sports cars and lowered vehicles moving onto trailers or a four-post lift. Their 3.5-inch height and 31.5-inch length address clearance, while a notched, textured surface with anti-slip pads helps them stay positioned.

The 31.5-inch length and six-degree incline create a gradual transition intended to reduce scraping at low-clearance bumpers and spoilers. A 3.7-by-19.7-inch notch attaches to the trailer ramp, and the textured surface plus anti-slip pads help keep the ramp from shifting during loading. Each polypropylene piece is rated for 4,409 pounds and stands 3.54 inches high. The pair can also be used with a four-post lift, extending its use beyond trailer loading.

Pros
  • Six-degree approach angle
  • Trailer-attachment notch measures 3.7 × 19.7 inches
  • Textured surface and anti-slip pads
  • 4,409-pound capacity per piece
Cons
  • At 3.54 inches high, it offers less lift than the 7-inch MaxRamps MRTX-7.

Skip it if you need seven inches of lift in a long solid-core ramp; MaxRamps MRTX-7 provides a 7-inch lift.

This pair suits owners loading lowered sports cars onto trailers or using a four-post lift who value a six-degree approach and a securing notch. Its 3.54-inch height sets the available rise.

Full product details
BrandHOXWELL
Color302
Dimensions31.5"L x 19.69"W x 3.54"H
Load Capacity4409lbs/PC Pounds
ManufacturerHOXWELL
Part NumberNBTS302
MaterialPolypropylene (PP)
Model NumberNBTS302

Listed on Amazon as: 3.5" H Trailer Ramps Avoid Bumper Scrapes, Low Profile Plastic Car Ramps 6 Degrees Approach Angle for Sports Cars Lowered Vehicles, Fits 4 Post Lift, Trailer Loading, Anti-Slip, 2 Pack

View on Amazon
ROBLOK 6-degree Trailer Ramps

#5

5. ROBLOK 6-degree Trailer Ramps

  • Dimensions: 31.5"L x 19.7"W x 3.5"H
  • Load Capacity: 4409lbs/PC lb
  • Material: Polypropylene (PP)

Best for: Sl absolutely low trailer transitions.

Why it ranks #5: These 31.5-inch polypropylene ramps are intended to pair with trailer ramps or lifts, with a 6-degree approach and listed 4,409-pound capacity per piece.

A six-degree approach across 31.5 inches gives the ROBLOCK pair a gradual transition for low cars climbing onto a trailer, rollback truck, or lift. The 3.5-inch profile targets limited-clearance vehicles, and its non-slip honeycomb design adds surface grip during loading.

The 31.5-inch length and six-degree angle are intended to stretch the transition from an existing trailer ramp or lift, helping low-profile cars climb with less scraping risk. A non-slip honeycomb design addresses traction at the contact surface. Each polypropylene ramp is rated at 4,409 pounds, with a 3.5-inch height; together, these features suit a starter-ramp role for low cars, trailers, and rollback trucks rather than providing a tall service lift.

Pros
  • Six-degree approach angle
  • 31.5 × 19.7 × 3.5-inch dimensions
  • Non-slip honeycomb design
  • 4,409-pound capacity per piece
Cons
  • The 3.5-inch height provides less lift than Pyle PVR30P2's 6.3 inches.

Skip it if you need more than 3.5 inches of lift for maintenance access; Pyle PVR30P2 provides a 6.3-inch lift.

For a low car that needs a gentle transition onto a trailer, rollback truck, or lift, this ROBLOCK pair offers a six-degree angle and textured surface. Its 3.5-inch rise limits maintenance clearance.

Full product details
BrandROBLOCK
ColorRbts302
Dimensions31.5"L x 19.7"W x 3.5"H
Load Capacity4409lbs/PC Pound
ManufacturerROBLOCK
Part NumberRBTS302
MaterialPolypropylene (PP)
Model NumberRBTS302

Listed on Amazon as: 2 PCS Low Profile Car Ramps with 6° Approach Angle, 31.5"x19.7"x3.5" Trailer Ramps with Non-Slip Honeycomb Design, 8800 LBS Load Capacity Starter Ramp for Low Car, Trailer, Rollback Truck

View on Amazon
Vraxelor 4-inch Trailer Ramps

#6

6. Vraxelor 4-inch Trailer Ramps

  • Dimensions: 36"L x 12"W x 4"H
  • Load Capacity: 3000 lb
  • Material: Eva Foam

Best for: Compact EVA trailer ramps.

Why it ranks #6: The 4-inch EVA foam pair has a 5.5-degree approach, a 5-by-2-inch trailer notch, and a listed 3,000-pound capacity.

A 5.5-degree approach across a 36-inch-long, four-inch-high ramp gives this Vraxelor pair a compact path for lowered cars and sports cars. The built-in five-by-two-inch notch is intended to meet the trailer edge, while EVA foam provides the ramp material.

The four-inch model is specified at 36 inches long with a 5.5-degree approach, a compact option for loading low-clearance vehicles where a longer ramp is not needed. A five-by-two-inch notch is designed to fit against a trailer, helping address the edge transition. The EVA foam pair has a listed 3,000-pound capacity. The product information also describes a 5-inch model with different dimensions, but this listing's specifications identify the 36-by-12-by-4-inch version.

Pros
  • 5.5-degree approach angle
  • 36-inch length and four-inch height
  • Five-by-two-inch trailer notch
  • 3,000-pound listed capacity
Cons
  • The 36-inch length is shorter than Chantmo Trailer Ramp's listed 46 inches.

Skip it if you want a longer 46-inch trailer ramp; Chantmo Trailer Ramp lists that length and a 5.5-degree slope.

This Vraxelor pair suits lowered-car owners seeking a compact EVA trailer ramp with a notch at the trailer edge. Its four-inch height, 36-inch length, and 3,000-pound capacity define the fit and loading limits.

Full product details
BrandVraxelor
ColorBlack
Dimensions36"L x 12"W x 4"H
Item Weight20 pounds
Load Capacity3000 pounds
ManufacturerVraxelor
MaterialEva Foam
Model NumberXL-TCPD-260918-001

Listed on Amazon as: Low Profile Trailer Ramps, 4" Car Trailer Ramps with 5.5° Approach Angle, 3000 LBS Capacity EVA Trailer Loading Ramps with 5" x 2" Notch for Lowered Cars, Sports Cars & Race Cars, 2 Pack

View on Amazon
Chantmo 4-inch Trailer Ramps

#7

7. Chantmo 4-inch Trailer Ramps

  • Dimensions: 46"L x 14"W x 4"H
  • Load Capacity: 3000 lb

Best for: Long low-profile trailer ramps.

Why it ranks #7: Made for low-clearance vehicles loading onto trailers, this 46-inch pair has a 5.5-degree slope and a 3,000-pound combined capacity.

A 46-inch length paired with a 5.5-degree slope gives the Chantmo trailer ramp a gradual route for low-clearance cars loading onto trailers and raised platforms. At four inches high and 14 inches wide, its listed dimensions provide a broader, longer profile than compact starter ramps.

The 46-inch length and 5.5-degree slope create a gradual transition, intended to reduce abrupt contact with bumpers, splitters, and underbody parts. Its 14-inch width gives the ramp a broad listed footprint for trailer loading. The pair is rated for 3,000 pounds total, with each ramp supporting up to 1,500 pounds when properly positioned. At four inches high, it serves as a low-profile loading ramp rather than a high-rise maintenance platform.

Pros
  • 46-inch length
  • 5.5-degree slope
  • 14-inch width and four-inch height
  • 3,000-pound pair capacity; 1,500 per ramp
Cons
  • Its 1,500-pound per-ramp rating is lower than HOXWELL NBTS302's 4,409 pounds per piece.

Skip it if you need a published capacity above 1,500 pounds per ramp; HOXWELL NBTS302 lists 4,409 pounds per piece.

This pair fits owners moving low-clearance cars onto trailers or raised platforms who want a 46-inch run and 5.5-degree slope. Keep its 1,500-pound per-ramp limit in mind when planning the load.

Full product details
BrandChantmo
ColorBlack
Dimensions46"L x 14"W x 4"H
Load Capacity3000 Pounds
ManufacturerChantmo
Model NumberTrailer Ramp

Listed on Amazon as: Trailer Ramp, 4 Inch Low Profile Car Ramps, 3000 lb Pair, 5.5° Slope

View on Amazon
Mytee Products Starter Tow Ramp

#8

8. Mytee Products Starter Tow Ramp

  • Dimensions: 10"L x 10"W x 10"H
  • Material: Nylon

Best for: Steel-bed transition bridges.

Why it ranks #8: Sold in pairs, these 2-3/8-inch ramps are designed to bridge a flatbed carrier or trailer edge, with a tapered profile and 10-degree slope.

A 90-degree notch paired with a smooth 10-degree incline lets this Mytee Products starter ramp bridge the gap from a steel-bed carrier or trailer ramp to ground. The curved bottom edges address uneven transitions, while the tapered, 14-inch pair is specified for low-profile cars.

The square profile and 90-degree notch are intended to meet the carrier ramp, while curved bottom edges help the pieces transition to uneven ground. A smooth 10-degree incline gives low-profile cars a ramped entry rather than an abrupt step. The glass-fiber-reinforced nylon construction resists wear, oil, and grease, practical traits around working haulers. Sold as a pair, each ramp measures 14 by 8 by 2-3/8 inches; the supplied facts list no load capacity.

Pros
  • 14 × 8 × 2-3/8-inch pair
  • 90-degree notch and square profile
  • Curved bottom edges for uneven surfaces
  • Glass-fiber-reinforced nylon resists wear, oil, and grease
Cons
  • No load-capacity figure is supplied, so its rated hauling limit cannot be assessed.

Skip it if you require a published per-ramp load rating; HOXWELL NBTS302 lists 4,409 pounds per piece.

Choose this pair when a steel-bed rollback or trailer has a ground-level gap to bridge and the square notch suits its edge. The 10-degree slope and compact 14-inch length are relevant fit considerations.

Full product details
BrandMytee Products
ColorYellow
Dimensions10"L x 10"W x 10"H
Item Weight4.06 kg
ManufacturerMytee Products
Part NumberTOWRAMP-814
Manufacturer Warranty DescriptionNot applicable.
MaterialNylon
Model NumberTOWRAMP-814

Listed on Amazon as: Mytee Products 14"x8"x2-3/8 Starter Tow Ramp for Steel Bed Rollback, Car Carrier, Hauler, Flatbed, w/Square Profile & Curved Bottom Edge – Safety Detachable Extendable Car Ramp Set – 2-3/8" Lift

View on Amazon
ROBLOK Low-Profile Garage Ramps

#9

9. ROBLOK Low-Profile Garage Ramps

  • Dimensions: 17.5"L x 10"W x 3.14"H
  • Load Capacity: 5 ton
  • Material: Plastic

Best for: Garage jack-access ramps.

Why it ranks #9: These 17.5-inch ramps provide a 2.6-inch lift and 10-inch width for low-chassis maintenance, but are less suited to loading onto a trailer.

A 17.5-inch length leaves room for a jack and other tools beneath the vehicle, making these ROBLOCK ramps useful for garage maintenance on low-chassis cars. Their 10-inch width accommodates wider modified tires, while the tire placement position provides a 2.6-inch lift.

The shortened 17.5-inch form is specifically intended to keep the jack's working area accessible, so buyers can position a jack and tools under the chassis without the ramp extending as far. Its upgraded 10-inch width addresses overhang from wider modified tires. The plastic pair has a listed five-ton capacity and raises the tire placement position 2.6 inches, making the setup a modest lift for service tasks rather than a trailer-loading ramp.

Pros
  • 17.5-inch length leaves jack working area accessible
  • 10-inch width addresses wider modified tires
  • 2.6-inch tire-position lift
  • Listed five-ton capacity
Cons
  • The 2.6-inch lift is lower than the 6.3-inch Pyle PVR30P2 maintenance ramps.

Skip it if you need 6.3 inches of clearance for under-car service; Pyle PVR30P2 offers that lift with a 17-degree incline.

This pair fits garage users who want jack access and a modest lift for low-chassis cars, especially when wider tires make ramp width relevant. Its 2.6-inch tire-position height is the main clearance boundary.

Full product details
BrandROBLOCK
ColorTs265-2 Packs
Dimensions17.5"L x 10"W x 3.14"H
Item Weight5.3 pounds
Load Capacity5 ton
ManufacturerROBLOCK
Part NumberRBTS265
MaterialPlastic
Model NumberRBTS265

Listed on Amazon as: Car Ramps for Lift and Vehicle Maintenance, Portable Low Profile Car Ramps for Garage, Heavy Duty Tire Ramps with 2.6" Lift Height for Low Chassis Cars and Support Jack, 17.5"x10"x3.14", 2 PCS

View on Amazon
Pyle Heavy Duty Vehicle Ramps

#10

10. Pyle Heavy Duty Vehicle Ramps

  • Dimensions: 36"L x 13"W x 8.5"H
  • Load Capacity: 13000 lb
  • Material: Plastic

Best for: High-clearance maintenance users.

Why it ranks #10: The 13,000-pound listed capacity suits maintenance lifting, but its 17-degree incline and 6.3-inch lift make it a weaker fit for low-car towing.

A 6.3-inch lift creates room for oil changes, tire service, and under-vehicle work with the Pyle PVR30P2 ramps. Their 17-degree incline, non-skid design, and stated 13,000-pound total vehicle capacity pair maintenance clearance with a portable two-piece setup for compatible vehicles.

The 6.3-inch lift creates space for service tasks such as oil changes, tire work, and under-vehicle access, while the 17-degree incline sets the entry angle. A non-skid design addresses stability during positioning. The pair is rated for up to 13,000 pounds total vehicle weight and is described for cars, light trucks, SUVs, and other compatible vehicles. At 36 by 13 inches, the plastic ramps suit maintenance use; their steeper angle differs from gradual trailer-loading ramps.

Pros
  • 6.3-inch lift for maintenance access
  • Non-skid design
  • 13,000-pound total vehicle capacity
  • 36 × 13-inch plastic ramp dimensions
Cons
  • The 17-degree incline is steeper than the six-degree ROBLOCK RBTS302 trailer ramps.

Skip it if you need a gradual six-degree trailer transition rather than a maintenance lift; ROBLOCK RBTS302 has that approach angle.

Choose these for compatible cars, light trucks, or SUVs needing clearance for garage service rather than a shallow trailer approach. The 17-degree incline and 6.3-inch lift are the key fit considerations.

Full product details
BrandPyle
ColorBlack
Dimensions36"L x 13"W x 8.5"H
Item Weight16.1 pounds
Load Capacity13000 Pounds
ManufacturerPyle
Part NumberPVR30P2
Manufacturer Warranty Description1 year warranty.
MaterialPlastic
Model NumberPVR30P2

Listed on Amazon as: Pyle Heavy Duty Vehicle Ramps | 13000 lb Capacity Car Ramps for Low Clearance Vehicles with 6.3 Inch Lift and 17° Incline | Portable Non-Skid Car Ramps for Oil Changes, 2-Pack, Black.

View on Amazon

Avoid ramp mismatch at the trailer transition

A ramp can have ample capacity and still fail to solve the main loading problem if its shape does not meet the trailer edge. The Mytee Products Starter Tow Ramp is specifically described as bridging the gap between a carrier or trailer ramp and the ground; its square profile and curved bottom edge serve a different role from a long, gradual loading ramp. The Race Ramps Foam Trailer Loading Ramps instead use a built-in 5-by-2-inch notch to connect to a trailer door.

Before buying, compare the ramp’s notch or edge profile with the actual trailer lip, ramp door, and ground contact point. A mismatch can leave an abrupt step or an unstable transition.

The listed dimensions do not confirm compatibility with a particular trailer, so measure the connection area and verify how the ramp is intended to sit before loading.

Ramp capacity is not the whole vehicle-weight check

A stated ramp capacity does not by itself confirm that a pair will safely support every vehicle in every loading position. These listings use different capacity descriptions: Race Ramps Tow Ramps 74-inch HD lists 1,500 pounds, MaxRamps describes 1,750 pounds per ramp and 3,500 pounds per set, while HOXWELL and ROBLOK list 4,409 pounds per piece. The Pyle figure is 13,000 pounds total vehicle weight, a different kind of claim from a per-ramp rating.

Do not compare those figures as if they were stated on the same basis. Check whether the manufacturer’s capacity applies per ramp, per pair, or to total vehicle weight, and account for how the vehicle is positioned.

The ROBLOK garage-ramp listing also recommends wheel chocks when equipment is parked or raised; use appropriate safety measures for the specific loading or maintenance task.

How to Choose Tow Ramps for a Low Car

Approach angle and ramp length

Look for the gentlest approach that fits your available space and loading setup. The listed trailer options range from Race Ramps Foam Trailer Loading Ramps at 4.3 degrees to 5.5 degrees for MaxRamps and several 4-inch trailer ramps, 6 degrees for HOXWELL and ROBLOK starter ramps, and 17 degrees for Pyle. Length also varies: the Race Ramps and MaxRamps hauler models are 74 inches, while the compact ROBLOK garage ramps are 17.5 inches.

A longer, shallower ramp favours a very low splitter or bumper when the trailer has room; a shorter ramp favours compact maintenance use, but may not suit a low car approaching a trailer.

Fit, profile, and connection

Match the ramp’s shape and dimensions to the trailer lip, bed, tire, and ground where it will sit. The 74-inch Race Ramps tow model is designed for flatbed trucks; the Mytee Products Starter Tow Ramp has a square profile, curved bottom, and 90-degree notch for bridging a carrier or trailer edge. Race Ramps Foam Trailer Loading Ramps include a 5-by-2-inch notch for a trailer door, while the HOXWELL listing describes a notch that attaches to a trailer ramp.

Short ramps such as the 17.5-inch ROBLOK garage pair favour service access, not trailer loading. Measure contact points and available space; do not assume similarly described ramps connect in the same way.

Capacity and construction

Check the capacity basis as well as the material, since these listings do not all express load ratings in the same way. Race Ramps Tow Ramps 74-inch HD lists 1,500 pounds, and Race Ramps Foam Trailer Loading Ramps list 1,500 pounds per ramp; MaxRamps specifies 1,750 pounds per ramp. HOXWELL and ROBLOK state 4,409 pounds per piece, while Pyle lists 13,000 pounds total vehicle weight.

Materials range from solid-core or coated foam to polypropylene and nylon. A lightweight ramp may suit frequent handling, while a plastic starter ramp may suit pairing with existing equipment.

Select only after confirming the manufacturer’s rating matches your intended use and vehicle loading.

Which tow ramp should I choose for my low car?

For flatbed towing with a low-clearance car, choose Race Ramps Tow Ramps 74-inch HD: it is designed for that use and has a solid core and 74-inch length. If your priority is a gradual trailer transition with a door connection, Race Ramps Foam Trailer Loading Ramps offer a 4.3-degree approach and built-in notch. Choose MaxRamps Car Hauler Ramp 7-inch when a one-piece 74-inch ramp and its stated 1,750-pound-per-ramp capacity suit your setup.

For a short starter ramp to extend a trailer or lift, consider HOXWELL 3.5-inch Trailer Ramps or ROBLOK 6-degree Trailer Ramps. Mytee Products Starter Tow Ramp is the more specific choice for bridging a bed-to-ground gap.

The compact ROBLOK Low-Profile Garage Ramps and Pyle ramps are better aligned with maintenance than trailer loading.

Frequently Asked Questions

How do I confirm a ramp will fit my trailer or rollback bed?

Measure the bed or trailer approach area and compare its available space with the ramp’s length, width, height, and profile. Check that the ramp can sit securely and align with the vehicle’s tires. Also confirm that any notch or connection point matches your trailer setup.

How should I position and secure ramps before loading a low car?

Place ramps on a stable, level surface, aligned with the tires and the intended loading path. Check that they cannot shift and follow the ramp and vehicle instructions for securing them. Approach slowly, and stop if a ramp moves or the car’s clearance becomes a concern.

What capacity do I need when a vehicle’s weight is unevenly distributed?

Use the capacity required for the load on each ramp, not just the vehicle’s total weight divided evenly. Weight can differ between axles and sides. Check the ramp’s stated per-ramp or pair capacity and choose a setup that accommodates the actual load distribution.

When does a built-in notch matter for trailer loading?

A notch matters when you need the ramp to connect with a trailer door or another matching edge. The Race Ramps Foam Trailer Loading Ramps are described with a built-in trailer-door notch and a 4.3-degree approach. Confirm that the notch suits your trailer before choosing this design.

Which ramp style suits flatbed towing versus garage maintenance?

For flatbed towing with a low-clearance car, the 74-inch HD Tow Ramps are the leading choice described for that use. Compact garage ramps, including the ROBLOK and Pyle options, are better aligned with maintenance. Choose according to the loading setup and the job you need to do.

Final Words

For flatbed towing with a low-clearance car, the 74-inch HD Tow Ramps are the clearest fit in this group. If a gradual trailer transition and door connection matter more, consider the Race Ramps Foam Trailer Loading Ramps. The MaxRamps one-piece ramp is another option when its stated per-ramp capacity suits your setup.

For any choice, verify fit, clearance, intended use, and capacity before loading.

Leave a Reply

Your email address will not be published. Required fields are marked *